you see like the alternator, it self excites at a certain high rpm, ONLY if capacitors are properly connected. it uses no outside power. it draws its field from the rotor just like the alternator did. there are several ways to do this.
We were close with the alternator, but we was lacking this knowledge. Look at these setups, then look at what we was doing. it will come to you.
I was in the process of putting permanent magnets inside the 10 HP 3 phase generator, then I realized there was no need to do that as it was a wast of money. A solution was to add a few capacitors.
Stevie, you need to find you a 3 phase motor to play with. and make it generate electricity with a driver motor, I say for you to study how its working, then maybe you see what i do.
Stevie, the known system has a great amount of resonating current flow at idel with no load. Talking about the iduction motor to generator here. There is a man on youtube that shown the current flow between the caps at idle. it was good, it was resonance, which is why it self excited.
Not sure if you know this, Stans alternator came off of a vehicle like an ambulance.
Anyhow, And Alternator can be set up as a (SEIG) and the Rotor doesn't have to even be exited
You can control the voltage going into one field of the SEIG to alter the amplitude modulation.
The rotor in Exited state like we do with the pwm is just a circuit in place where a capacitor should be
There is a certain Speed where the Alternator will self exit just like the SEIG.
My point, The SEIG as known is not, and has not become known to the Alternator Design here of stans that we have been playing with. Researching the SEIG in 2 capacitor mode, and also 3 capacitor mode should indeed be Understood before hands are laid on the current alternator water fuel cell design.
Remember the Injectors stan put on the other guys car in that article. Think about how this work outlaw, Put your mind to work here.
You move superheated water from injector to Cylinder without disturbing the superheated water. The water doesn't bust into a mist like with a diesel injector because the goal is to move a liquid without disturbing it. Once the piston starts down the boiling point is lowered, The water Explodes forcing the piston down.
This is why diesels run on superheated water with the right injector that can move enough water.
my ex girlfriend has left me I have two children with her, she has cost me over $5,000 she has taken my home away from me but I get my house back Monday I am NOT married to her but in Alabama she is trying to file common law marriage which I am also fighting. I have had so much going on since I have been here I have not been able to do anything. I have two businesses I have to run the heating and cooling business which requires by the state of Alabama that I know the BTU's it takes to heat 1 gallon of water and all that good stuff. I'm required to know how refrigerator converted verted Exedra. she got the lab with a house and I am concerned with my stuff. enter the fellow that is skeptical to my post, the atomic levelexplaining an atom when it comes to the water molecule is possible I will always believe that but that is not what Stan was doing.
you should have put a capacitor across the bridge of good value and then when the water reaches a certain temperature the amperage would drop to a minimum and you could lower the voltage and idle. it takes a tremendous amount of electricity to heat the water but after it is heated to a certain degree this electronic system it's an idol because the water keeps its heat it does not cost much to keep the water thermal it is just getting it to that point is when you pay this is what people fail to understand. to answer your question I provided a website the goes into detail but 1 BTU is equal to 3. 412 watts i think. it depends on the temperature your going to raise the water to and it also depends on what you're going to be doing with a water rather it just sitting there are you using a small amount at a time those formulas have to be calculated, which I do not look at formulas and I do not look at it scientifically. I look at what's happening the big picture is electricity goes in the water gets hot pressure is applied the water cannot exist at that temperature in an ambient pressure and it explodes. Stevie any injector that will open a good amount and its end will do the job since the behavior of the water does not like a ambient pressure. Stevie when the water is injected at that temperature and that pressure the piston moves down so there is a pressure drop immediately when the water is it a very high temperature. it is like the fuel was moved from the injector to the cylinder before the piston starts its way down, once the piston starts his way down the pressure drops rapidly then the water that was transferred from the injector to the cylinder explodes.
Do you not understand water several hundred times greater in temperature than its boiling point is possible only because a higher pressure was applied. do you not understand what bringing this water at that form to an ambient pressure will do? the water can be stored at a temperature when there is no Sun hurry up china is waiting. coal not the answer when their windmills and solar cells are not working. The great time of trouble is now!
Stans sila was destroyed, man you people, why do you think stan had designed glass sunligh to heatvlenses for? Why do you think he kept melting the metel in that silo? Look no further, it is not the hydrogen you want from water, look here, it is the power that comes from the water contaminated or not. Set your fuel cells to the side for just a moment, what do you have to loose? Go heat a hot water heater at a high pressure then shoot it with a gun, then would you see? Go take the radiator cap of of your uncles old ford when its dangerously hot, then would u understand? The water wants to move! You all have been blinded by that cell stan used to heat the water. Go back and look at the boiler plate, dont be fools.
Do you not understand water several hundred times greater in temperature than its boiling point is possible only because a higher pressure was applied. do you not understand what bringing this water at that form to an ambient pressure will do? the water can be stored at a temperature when there is no Sun hurry up china is waiting. coal not the answer when their windmills and solar cells are not working. The great time of trouble is now!
Have you built this circuit yet. Please overlook the 900 Ohm resister as its a 1k one. It shouldn't be Crucial as long its within a 100 Ohm range to Replicate the above circuit. This should only take 5 minutes of your time to construct. 10 mins to find the parts.
A typical 9 volt battery is between 300mah and 500mah. So since this isn't actually field work here but "thoery only", let's just assume the battery is anywhere between 300 to 500 mAh, doesn't matter because it is the ideal we are after here And not firm solid legit perfectly crunched numbers. Let's crunch what we have and get a rough estimate.
With that being said. What would be your best bet using 13 batteries 9v. ? 5 seconds, 5 mins? 15 mins? And would it be benifittable to add 13 more in parallel. Let's assume we used 52, so that's 4 9v in parallel.
So, the 9v cell will drop when consuming 300ish milliamps after how long? Haw many must be in parallel to solve a 8 hour runtime? Let's go with 9 colts here.
Where did this website go stevie? I'm not certain this is the correct address. Also, could you message me all the old domain names, Im wanting to see some of my old work on those old website.
Also stevie, what was the name of that one waterfuel site that was not on the google search, it may have been a secret one. I have NO memory of those addresses.
Sorry for Poll posting. I would like to add. My Shunt diodes are 10 amps per diode. I have fried one with over current of a primary coil of about .9 ohms. I have had to shut the system down because twin shunts overheated. I have used a 5 UF capacitor that never got hot, but made the Primary coil THUMP and it took the place of the Shunt. I have Also used a Inductor. There is somthing here to this puzzle when debating a Shunt and Cap, or inductor.
My Next step is putting a Shunt with a Inductor. Their cant be a Resistive load greater than the FET or the current will pop the fet. At this time my thoughts are the Shunts secondary inductor must be greater in size and smaller in resistance than its primary coil. I Plan to research this further later.
I have a few of stans patents I need to print out.
Could someone Please Post the patent numbers to stans most Basic patents here for me to print off. Or direct me to the most basic ones, and where the best place is to get them as my time is limited to the point any effort you put in to help me will be greatly appreaciated.
I was told stan did not try and hide anything, and I believe that. Also, do any of you guys know where I can salvage a SCR, if not, I will have to buy one and at this Time I do not have the funds. Any donations will be greatly appreaciated. Even if it is a SCR you want to mail me. My soldering iron broke, and Im waiting on one in the mail. Im currently using an old one and its a bitch.
Message me if you need my address, to anyone that wants to mail me any cores, Scr's, or the like. I am not asking for money. If no one contributes thats ok, I understand. I will still continue to do what I can and post what I find.
I really need a 6" acrylic tube 13" long for my old tube cell. I do not even know where to purchase this. Any links for that or donations will be great! Thanks guys.
My Main focus is to Search Stans Patents for this area on the shunt. Any Info if you have any of this knowledge on hand would be greatly appreciated!
What we know as to date, Stans technology was based on the alternator which had a IRON core, I must look into that setup for a ferrite choke. I dont think their is one. I am Weeding out much. I have distilled water here for testing purposes. I will test as I can, Normally once a week. When I perform test, I have help, and I do not sleep on those days.
Look forward to seeing Facts threw testing not guessing. I have recently in the last 2 days Made a Ferrite core VIC, I have tested in a few different ways. More results Later on that.
I am finding out you have to have a SCR, that is a Diode with a Gate Trigger to turn it off and on. Stanley had a Photo of a SCR on one of his VICs but it was not labeled.
Stevie, Go ahead and Collect you a SCR. Unlike our time together before stevie, I will be working with you in the same manner I have in the past few weeks.
It is possible the SCR was triggered on its Highest peek.
I know I stated the Resonance on the diode off time, But I was getting results, Cold ones. BUT, I have seen other things that have also caught my eye. THE SCR IS ONE OF THEM!
Get your SCR's, and standby for further findings.
I am noticing allot more on stans patents that I did in the past. We have all been working on this a long time. I look to further stans technology than what we already have it. I look to do this with you guys as my friends and best group!
