Dankie

the lawton works with the gate and frequency on the same side going into the vic using one transistor.... couldnt you supply a constant freq source of 0-20khz with one transistor on the input side then have you gate/switch transistor/ gate on and off on the neg side?? wouldnt that isolate the vic during pulse off time from ground(neg)? the current on  time will be contradicting it self in a form of impeadance in a since??. it would be as if its compounding electrons toward the 90 degree center tap of secondary. output. to ss neg. since the current and freq effect the displacment in secondarys.. by doing so  the ss take on a potential difference in a step up pumping action with diodes working as back flow preventors..  and what i mean by potential difference is that the negative is being forced with more electrons then normal.  and the positive is having a 1 to 1 ratio jump in holes (positve charge) during displacement.. that will allow potential to build in a step up manner.. and when it comes to discharge its not in to much of a hurry since the charges would most likely want to stay in the choke since there bifilair wound next to each other they would be highly attracted to each other at a balanced ratio.. and there is no difference to cause the current across water for balance. i would say a true -400 and +400  potential the negatives extra electrons would be the exact amount needed to make the positve back to neutral. so if you have -500 and +400 your system probly isnt isolated and is getting extra electrons from some where throwing it off balance.. that would cause your bifilar to create current flowing  50 volts worth of neg potential(electrons) through the water to the positive side to make -450 and +450.. well if theres a imballance like this from stray electrons finding there way in system it  will create imbalance and force  current non stop so it will fail. not sayn this is right just a perspective.

now think on this people.. in stans data he says the ss choke are coated with a 3 kv rated insulator.. i bet you dont have more then 3 kv going to the injector.. remember less winds then secondary typicaly 11.6 k resistance. a step down. the secondarys insulation is not as much a concern for its insulated properties.. its displacement is being isolated in a step up manner by the delrin. it doesnt have a high difference sitting right next to it like bifilar ss chokes.... when you read dual secondarys that means its like bifilar but the displacement is going in same direction.  and is said to allow an accelerated magnetic induction to the core compared to a single wound. all perspective/ insight


outlawstc

the voltage between each widing is much smaller than 3kv

It is , I wonder if theres a dual primary on the VIC .

I wonder is the particle oscillation follows some sort of resonant frequency .

Lol amazing , nothing in the media about this lol....

The SOB is 82 years old, he has nothing to lose for devulging his secret if it is indeed legitimate.

Who knows the reasons why he would not reveal .It may be more complicated than we think .

Or maybe it is a fraud . I heard the Phillipones are now running their power generation plants with 70% water and 30% gas .

Maybe its payback time , the elites are loosing their grip on these asian countries , they cant dominate them much longer .

Poor guy , it seems he will be alrite .

Excellent ideas Dankie! I was reviewing the info Steve posted and I noticed the intake ionizing system utilized the LED arrays. This is not a big deal other than finding who sells these. Any Ideas?

Im glad you like the idea , it is more a logical thing , I see the core I say hey , theres a bunch of magnetic lines in the middle , why not use this as a gas processor and insert some HV .

hmmmmmmmmmm, if you do the calculations required to keep h2o above freezing at 1 cal. per gram per degree C. you'll see that a goodly amount of energy needs to be sustained and expended.  it's lot to ask of the battery if the engine is not running.

Thats because the Steam resonator is like a godly efficient heater and is on its own an OU like device .

Its works with "particle impact" as they say ...

Hes got that steam resonator thing getting switched on if the water passes a cartain treshold .

This is always on even when the car is shutoff .

A tiny pulses of energy every 20 minutes or so keeps the water warm for the next day .

Even I could do that if I had the steam resonator .

Why dont you go ahead and do it and make the PLL or any pulser you may find more easy , learn ltspice and read about the PLL circuit . Many have made it work .

You dont "HAVE TO" make a circuit such as this one to test out Stan's main ideas .

Yeah thats a nice big circuit , it can be simplified with a dc biasing im pretty sure .

Altho you should make that one , it just has that official working look , mine was made in 30 minutes , I was pcbing and had the idea .

LOL MORE COFFEE , MUST FINISH !!!

Looks like I will be late once again .

Only 10 days left before school , the pcb will take at least 2-3 weeks to come in .

Today im ordering it yep , bored out of my mind recheking for mistakes .

O yea , use the lm3900 as a dc op amp.

Here is something that will time everything perfectly .

No overlap , a few nano seconds before the HV stops , the static pull begins .

Give it a try . For mosfet driver theres alot out there , very simple to operate if you consult any datasheet , all the instructions are there for even complete noobs to operate . But you must keep leads very short and wide . No more than an inch between mosfet driver and mosfet and large wire , I use very wide planes for mosfet on my pcb .

This circuit is on my pcb , you can have auto-gating with either  divide by 2,3,4,5,6,7,8,9,10 on a rotary switch or divide all those by either 2 or 4 once more .

So a maximum of divide by 40 spacing . For asymetrical gate/pulse ratios you must use manual jolt gating.

Yes I am the #1 LOL .

Low-side mosfet = N Channel mosfet

High-side mosfet = P Channel mosfet

All of these logic gates are different gates , no exeption , only their numbers are the same because I copy pasted , dont let that confuse you . Wired as is

I Think there should be a diode in parallel with the fuel cell... 

The EEC is exactly related to Meyers don , I dont understand your point .

So that diode mean high voltage across the tubes warp , I guess it does ?

Anyways I am not messing around with this old Stan stuff .

I am moving on with my new Stephen Meyers driver unit I should be getting in 2 weeks . Stephen seemed to be saying that Stan's design were not researched enough ... Perhaps it was based on Stan's intuition and not fully researched as to what was causing the extra production . As stated by Stephen that even he still didnt know what exactly was going on with Stan's cell .

No positive news from Hardkrome yet regarding the VIC .

Don , why should we figure out anything ? Test that VIC and show that it can work .

Dankie, you gotta get off the booze before it kills you!

See Qiman this is what this site has comed to , there is no leadership or no desire to do anything . There is just these hating old guys with a tubular cell  that didnt work and dont understand nothing further than metal and electricity flowing with some pulsing that they dont understand either . Somekind of old depressed town with boozers and a closed factory with 200 habitants .

I must move to the city Qiman .

You cant even come around this site doing stufff cause these guys just hate , but they dont build anything themselves and want everything , se basicly nothing gets posted besides this anecdotal **** about Stan's coloring book . The guys that know a bit dont even bother to come around anymore that much . 90% of em are like ghosts , spooky sometimes .

Shhh ... I dont drink booze @ this hour , in fact I am making an cad design plan for school .

And you gotta get yourself some skills because your skills are monkey see monkey do .

Yes I agree Qiman , this site is boring , I like energetic more now .

So Tutanko did something special ? Plz confirm that the video showed something awesome.

I work months to release a new product very nice for HHO research and this is how ppl act . Nobody even says good job . I release the best manual pwm in history on this site and nobody even builds it because my drawing didnt have all the component names and pins lol .

I pains me to say that energeticforum has the best threads and best researchers now . I feel alone on this site , can I plz come back to energeticforum.com . Im sorry If I insulted the site , I deeply regret . I promise I will be 100% following the site's agreement rules , 100% sware .

http://www.ionizationx.com/index.php/topic,1087.30.html

These peeps here never build anything serious , besides a few people this site is monkey see monkey do , they dare not avdenture themselves away from something they can copy word for word 

I will soon launch my product , see my project section for more details . Should be getting it any day now

Is a super oscillator/hvdc supply/dual solid state 3 phase pure sine alternator/ AM mixer .

I was even selling the pcb for people to build themselves for 200$ but pppl here sayd its too expensive . This is not a scam deal , even yet I risk being scammed and robbed because everything is exposed ,  just so I can start a new round of research of my HHO passion , HH0 has been stalling so it needs a boost .

Well dont start begging or whining at him , that just makes him wanna not share .

They are gonna sell these things soon , life rent and copyright laws just like a car or any other product . Maybe if you smart enough you can build , invent or replicate one for less , thats it , they will leave you alone but dont break the laws .

You cant buy vcr today that can be replicated LOL . Its all private components etc ... What you expect from energy LOL ...

I dissed and cursed both Aaron and he a few months back , I am now banned for life .

Could go back with a prozy but that site is not worth reading , so much crap everywhere .

So much crap these days , there was gray motor thread was good tho , had a good video replication , thread is dead now ... silly noobs ...

Lol good one Steve , funny .

But seriously , plz clean up the site from all this junk .

This is a water for fuel research site .

Good posts have been buried by this crap .

Well I dont think he was acting , that guy Joseph Newman has the same attitude if you watch his video .

Most inventors are religious .

And hes keeping it secret , just like Stan .

Well thats great outlaw , theres nothing like a good book .

I love geo-political books , I never really read much till I knew how interresting things really were lol .

I am currently reading Zbigniew Brzezinski's the grand chessboard .

 Theres alot of mediocre authors , have to research the good ones .