Bench
424 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established WFC
In Example I, the water capacitor of the fuel cell consisted of two concentric cylinders 4 inches long; the outside cylinder was 0.75 inch OD, the inner cylinder was 0.5 inch OD, with a spacing of 0.0...
established WFC
A preferred construction material for the water capacitor plates is stainless steel T-304, which is non-chemically reactive with water, hydrogen, or oxygen, and is electrically conductive yet inert in...
established WFC
A pulsating uni-polar voltage field first aligns/polarizes water molecules, then elongates them as energy cascades in incremental steps with each pulse, until the applied electrical force exceeds the...
established WFC
The water capacitor is preferably chemically inert and no electrolyte is added to the water; the goal of the circuit is to prevent electron flow (current) through the water, since an idealized capacit...
established WFC
Natural water is stated to have a dielectric constant of 78.54 at 20°C and 1 atm pressure, a property used in forming the water capacitor with electrically conductive, chemically inert plates immersed...
established WFC
Under repeated pulsing, water confined between the capacitor plates takes on an electrical charge that increases via a step-charging phenomenon, with voltage continually increasing to about 1000 volts...
established WFC
Resonance in the circuit was achieved at a 26 volt applied pulse to the primary coil of the toroid at 10 kHz, causing water molecules to disassociate into elemental hydrogen and oxygen along with prev...
established WFC
The water capacitor of the fuel cell consisted of two concentric cylinders 4 inches long; the outside cylinder was 0.75 inch outside diameter, the inner cylinder was 0.5 inch outside diameter, with a...
established WFC
A preferred construction material for the capacitor plates of the water capacitor is stainless steel T-304, chosen because it is non-chemically reactive with water, hydrogen, or oxygen.
established WFC
Means for varying the physical spacing between the spatially positioned plate exciters are used to vary the rate of hydrogen/oxygen gas generation; this spacing variation is correlated with control of...
established WFC confidence 0.80
With multiple secondary windings on the rotating field, the number of output pulses equals the number of windings; pulse frequency depends on the rotational speed of the field, and the induced seconda...
established WFC confidence 0.80
When the input voltage is DC, it is converted to uni-polar d.c. voltage pulses using a rotating field with primary and secondary windings — the DC is connected to the primary winding, and a rectifier...
established WFC confidence 0.80
In a multi-plate configuration, positive potential is connected independently to each of one set of plates and negative potential independently to each of the other plates, with a resistive element co...
established WFC confidence 0.80
The resistive material sandwiched between the negative exciter plate pair comprises a resistive material combined with a binder; varying the percentage of binder varies the resistance of the material,...
established WFC
The exciter plate receiving negative voltage includes a ground connection and an electron-inhibiting resistive element (optionally variable) connected between the negative plate and ground to limit el...
established WFC
Means vary the amplitude of the uni-polar d.c. voltage duty cycle pulses to a minimum level sufficient to maintain resonance between the pair of plate exciters, while repetition frequency of the pulse...
established WFC
The pair of plate exciters are spatially positioned in the natural water with a physical distance between them equal to a wavelength corresponding to a particular frequency of the voltage's back-and-f...
established WFC confidence 0.80
The duty cycle of the uni-polar d.c. voltage pulses used to inhibit electron leakage can be varied periodically, aperiodically, or non-uniformly across a plurality of distinctive amplitude gradient le...
established WFC confidence 0.80
Means are provided to vary the amplitude of the duty cycle pulses and correlate their repetition rate with amplitude, producing an average pulse amplitude below the level that causes electron leakage,...
established WFC
A pulse forming circuit varies the duty cycle of the uni-polar d.c. voltage pulses to a predetermined repetition rate, inhibiting electron leakage as the amplitude of voltage applied to the plate exci...
established WFC confidence 0.80
The transformer in the AC-to-DC-pulse conversion circuit further includes variable inductive means for varying the output frequency of the voltage induced in the secondary winding, further inhibiting...
established WFC
The circuit for converting AC input voltage to uni-polar d.c. voltage pulses comprises a transformer having primary and secondary windings, with a rectifier circuit connected across the secondary wind...
established WFC confidence 0.80
When the AC input voltage's converted amplitude applied to the plate exciters is increased to a second level, the circuit further varies the frequency of the input AC voltage to further inhibit electr...
established WFC
The variable voltage source includes means for restricting current flow between the plate exciters to a minimum value relative to the applied potential difference, by regulating the repetitive frequen...
established WFC
The rate of production of the hydrogen/oxygen/other dissolved gas mixture from natural water is controlled by varying at least one of: the amplitude of the applied voltage, or the pulse repetition rat...
established WFC
The Water Fuel Cell generator uses at least a pair of plate exciters within a water-containing vessel, driven by a variable voltage source that converts input voltage to uni-polar d.c. voltage pulses...
established WFC confidence 0.80
The voltage amplitude is increased only to the minimum necessary to achieve resonance, then maintained at that minimum and raised further from there to increase gas generation; this minimum correspond...
established WFC
When the distance between the plate exciters equals the wavelength of the frequency of the pulses driving them, the back-and-forth movement of water molecules/atoms toward the attractive field goes in...
established WFC
In one typical structure of the apparatus the plate exciter voltage was varied from zero (0) volts to 45 volts, while in a smaller structure the lower voltage levels of FIG. 8 (up to 8.5V) were used i...
established WFC
The spacing between plate exciters in water (varied via rack 80 and gear 81, manually or by programmer 69 driving motor 33) is directly related to gas separation rate: closer spacing increases attract...