haithar

I'm going to watch steorn.com presentation live right now they will how the over unity principle and explain it right now in few minutes.

I missed the show and i'm waiting for the videos to be uploaded tomorrow. Did anything impressive happen? It was probably not the best idea to simply short the coil which acts as a heater instead of applying a lightbulb or something like that. Would have been more impressive.

http://gas2.org/2009/08/03/invention-uses-mountain-dew-for-fuel/

i don't see a problem, the ampmeter is connected right.
of course it will measure different amps then but the energy or power is the same, because the volts will differ too.
The bridge doesn't change the potential so he measures correct.

well in a series resonant circuit the current is always the same.
if we have  +-----L-------C------- the voltage at the coil will be 90° before current, and the voltage on the capacitor will be 90° behind the current, which makes 180° degrees voltage difference between the two parts.
if you measure the whole voltage over L and C and the current you will notice both will be in phase at resonance.

what's new about that stevie? does it help in any way?

If it's not a rms meter then you can't believe it to be correct. especially not if your powersource shows more power than your cheap outlet energy meter.

When the pulse is off, the coil discharges. That discharge is a high voltage pulse of the collapsing field.
In this setup you are getting 2 pulses for the price of 1.
It provides a much better efficiency!

Nice idea, but you need current to "charge" the coil, so your advantage in efficiency is gone, in fact you lose energy because of Lenz's law.

how's it going on with the mikrocontroller pwm?

Why does it work in a simulation but not in reality 

but it will eat up the voltage, even a 20Ohm. I don't know why the coil uses so much current even when pulsed at 50kHz. I think i have a short in the circuit somewhere or something like that.

btw you can get voltage to your water cell which is not insulated with this method!! Strangely enough i had to change the direction of the bifilar connections yet again.
unfortunately the amp draw in general is too big so i cannot test further yet. i'm also thinking of rectifying my 230V grid current which would give me about 350V DC i believe. I have a switching Mosfet for 600V so it would work. But the current is way too big at the moment.

But back to the circuit,
why does it work fine in this configuration (switch/mosfet parallel with cap) - i can get 70V at the capacitor from 30V at 0,1A - but why doesn't it work in the stanley meyer / richie burnett / tesla coil version at all? (same voltage but only 2V at the cap).

how would you integrate the step-up transformer into this circuit?
the only way i can think of is using a hv-mosfet. not the best idea

alright then i misunderstood the purpose of this circuit. it has lost interest to me because i'm not interested in current-electrolysis.

i looked into the data sheets for the diodes, aren't they oversized? even a 1n4007 does have a rating of 1000V/1A, which is 1000W, the diodes you mentioned can hold much much more, as i remember the concept was to inhibit current to the mA range.
why this large diodes?

24 hours earlier and i could have bought the diodes. I made a larger order today at an online store. Maybe i'll try in the future or use 1n4007s ... 

Quote from: haithar on April 12, 2010, 20:01:06 pm

Just saw this on a german forum.

It basically says he is creating ozone from air/water in addition to hydrogen (but not very much), the ozone is explosive and is fed into the ice for combustion.

Also note the production method, hv dc, water ...
http://en.wikipedia.org/wiki/Ozone#Laboratory_production

Actually the german wiki article is much better.
It says it will work with dry air and an inhomogenous electrostatic field, absorbs heat from the environment (!), will work with 316L stainless steel, and 90% of the energy which is put in will come out again as heat.

Whats the german link?
I like to read that too.

Steve

http://www.hohle-erde.de/cgi-bin/yabb/YaBB.pl?num=1115618840/69#67

Just saw this on a german forum.

It basically says he is creating ozone from air/water in addition to hydrogen (but not very much), the ozone is explosive and is fed into the ice for combustion.

Also note the production method, hv dc, water ...
http://en.wikipedia.org/wiki/Ozone#Laboratory_production

Actually the german wiki article is much better.
It says it will work with dry air and an inhomogenous electrostatic field, absorbs heat from the environment (!), will work with 316L stainless steel, and 90% of the energy which is put in will come out again as heat.

wow thanks reading over it. Luckily i understand german, because the translation is not the best.

Hello you all i'm coming up right now with info that anyone though before!
I solved the injector!

What happens when a conductor moves cutting a magnetic field?
A voltage is developed! in a direction 90° from the magnetic field lines and 90° from the movement!
What happen when we have water under a very high pressure and make it to pass thru a 0,40 mm diameter hole?
It will pass thru it at a very high speed!
water is not conductive thus ( the ionized gases were needed in the injector to create the conduction )
Lets say you have a 0,40 mm hole 6cm long (it will have a volume = to 7,5 ul ( the amount stan said was injecting for each injection cycle in each cylinder) accordingly to the volume of a cylinder calculation =((diameter/2)^2)*High)
Now you need to inject it in only 2ms what will be the speed of the water?
answer (6cm/0,002)*(7,5-7,4) ((volume of the tube - the amount of water to be injected) (this result is = to how many times the tube will fill per injection) well the result is almost 3000cm/sec
Now if you cut a magnetic flux of 15.000 gauss with water at this speed you will develop 1,7volts witch together with the ionized gas and a catalyzer element and resonance will actually crack the water!!!

Enjoy Freedom!

Now you just need to develop a certain pressure inside the tank, (only about 4 liters of water will be consumed in one hour thus even very high pressure will cost very low energy) and solenoids to do all the work...
What about this?
after 2010 years we can again walk on water...haha
Best Regards to you all
Donations are welcome! you find link on my you tube channel

Did you know that 7,4 ul of water = 13ml of gas  h2+02 witch represents 3,33% of the 400cc cylinders meyer were using.

Yes he used positively ionized ambient gas...

He created the injectors to simplify and lower the costs

I'm still skeptical, but the fact that the volume of 1l water is 1600l in HHO should account for a good pressure. Intriguing idea How do you want to create a magnetic field of 1,7T though? It should of course be permanent magnets as no current is needed to maintain the electric field.