Bench
1,315 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC confidence 0.80
Only several gigavolts (billionths of a volt) of applied power are needed to initiate molecular orientation; an amp restricting circuit (9XA, per Figure 20YD) allows this orientation process to occur...
established WFC
Because the water molecule's hydrogen atoms are positively charged and the oxygen atom is negatively charged, the applied analog voltage pulse causes random water molecules to spin and orient: hydroge...
established WFC
The analog voltage range (voltage intensity) applied across the excitor-plates is typically from zero to 5,000 volts and above, always positive relative to negative ground potential, with polarity rem...
established WFC
A unipolar Voltage Pulse Train is applied to the voltage intensifier assembly, forming an analog voltage pulse train that increases linearly from a low energy state to a high energy state across the e...
established VIC
The Magnetic Spin Generator produces A.C. electrical output when the pickup coil-array is series-wrapped Right-Hand to Left-Hand, and D.C. output when wrapped in the same direction; orientation coils...
established VIC
The permanently magnetized particles of gas prevent electromagnetic coupling between the orientation coils (12/13) and the pickup coils (2a...2n); instead, power input rotates/spins the gas particles...
established
To increase electrical power output, the non-magnetic tube (1a...1n) is spiral-wrapped through the pickup coil array (2a...2n), as shown in Figure 33, which increases the number of magnetic flux lines...
established VIC
When the orientation coils (12/13) are de-energized, the permanently magnetized particles (16a...16n) rotate another 90 degrees, reforming field (4) while field (3) collapses; the collapsing field (3)...
established VIC
When the variable gate circuit (EE) energizes both orientation coils (12/13) simultaneously, equal-magnitude fields (5/6) in North-South relation form across the air gap, terminating field (4) as the...
established VIC
To permanently magnetize the gas particles (16) inside the tube (1), an electrical potential is applied across the pickup coils (2a...2n), forming electromagnetic field (4) that jumps the air gap (7);...
established VIC
The Dual Pulsing Gate Circuit uses variable gate circuit (EE), electrically connected to both orientation coils (12/13), to apply a voltage pulse of given duration to both coils simultaneously (Figure...
established
The hollow non-magnetic tube (1) is filled with permanently magnetized particles of gas (16), and the circular assembly of orientation coils (12/13) forms an air gap (7) between them, as shown in Figu...
established VIC
The purpose of the Magnetic Spin Generator circuit stage is to oscillate a permanently magnetic field through a pickup coil without particle acceleration, using dual orientation coils (12/13) on oppos...
established WFC confidence 0.80
During water recycling, the water molecule is re-exposed to laser energy (per Figure 20FB and Figure 20K) for Energy Charging, described as duplicating sun exposure.
established WFC
A gas condensing assembly (40) attached to the catalytic block assembly uses a first-stage heat exchanger (15) exposed to flame temperature to heat a cycling gas passing through an expansion chamber (...
established WFC
Water purification is performed in three steps: contaminates remain in the Fuel Cell since voltage dissociates the water molecule; the sustained hydrogen flame kills bacteria attached to the Fuel Cell...
established WFC
A hemispherical-shaped Catalytic Dome (10), composed of heat-retaining ceramic material, is placed on top of and in spaced relationship to the quenching nozzle (20); it captures escaped combustible ga...
established WFC
A non-oxidizing material such as alumina (a ceramic) is used to form the quenching disc (7) to prevent gas port (5) enlargement due to chemical interaction and/or heat exposure; the nozzle assembly (2...
established WFC
Multiple Quenching Circuits (5a...5n) are used to prevent flame-out when the Fuel Cell gases exceed a certain gas velocity, and quenching circuits are prearranged so an adjacent flame can re-ignite ex...
established WFC
The Quenching Nozzle (20) prevents spark-back into the Fuel Cell during gas ignition; fuel gases pass through a small elongated gas port (5) smaller than .015 inch diameter but equal to or greater tha...
established WFC
The hydrogen gases support a flame temperature up to and beyond 5,000°F; to reduce burn-rate/flame temperature further, non-combustible gases expelled from the sustained flame are captured, flow-regul...
established WFC
The non-combustible ambient air gases retard the speed at which hydrogen atoms unite with oxygen during burning, automatically adjusting the burn rate of hydrogen gas from 325 cm/sec down to 42 cm/sec...
established WFC
Since water is the gas mixing regulator, the fuel gas ratio is composed of 2 hydrogen atoms to 1 oxygen atom plus 17% to 19% per part of ambient air gases, and this ratio remains the same regardless o...
established WFC
Since the Fuel Cell utilizes voltage to dissociate the water molecule, the Fuel Cell becomes a multi-gas generator, producing hydrogen, oxygen, and ambient air gases (water contains 17% to 19% per vol...
established WFC
The device directly uses utility power without the aid of an auxiliary amp generator.
established WFC
A self-cleaning fuel cell was developed by way of voltage application: voltage pulses perform a scrubbing action on the plates that prevents an oxidizing coat/film from forming (by retarding chemical...
established WFC
A quenching circuit was developed to prevent spark-back into the fuel cell, and quenching tube technology allows distribution of fuel cell gases without spark ignition.
established WFC
The system adjusts hydrogen burn-rate from 325 cm/sec to 42 cm/sec, co-equating fossil fuel burn characteristics, by using water as a gas mixing regulator.
established WFC
The described control features may be operated separately, grouped together, or actuated together in a systematic way, giving flexible control over gas generation.
established WFC
Power load to the exciter-array is sequentially switched (variable switching) while performing the voltage amplitude, frequency, and pulse-train functions, including in direct relationship to moving v...