Bench
1,315 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established WFC
The number of voltage pulses per gated pulse (pulse-train) is varied in direct relationship to both the variable voltage amplitude and the variable gated pulse rate, providing another control axis for...
established WFC
The pulse voltage frequency is varied in direct relationship with the variable voltage amplitude as a control mechanism for gas production.
established WFC
Increasing the voltage amplitude of the pulse increases opposite polarity attraction between charged particles, which in turn causes greater gas production.
established WFC
The fuel cell sustains a constant, high-temperature hydrogen/oxygen flame beyond 5000°F, with flame size controlled by amp flow, unlike prior art which requires a continuous gas-ignitor to maintain co...
established WFC
By using voltage attenuation with the fuel cell, ambient air is allowed to uniformly mix with the liberated hydrogen and oxygen gases, reducing the hydrogen gas burn-rate from 325 cm/sec down to less...
established WFC
Voltage attenuation as to voltage amplitude spans an extremely broad range, from one volt to over 5,000 volts, enabling high gas yield; prior art is limited by amp arcing that reduces electrode life,...
established WFC
The water fuel cell can produce more than 100 cc/min of gas output while only 1 amp of current leakage occurs, demonstrating high gas yield with minimal amp flow.
established VIC
In the rotary alternative (Fig 11A), variable amplitude pulsing circuit (21) energizes armature coils (22) to produce pulsating electromagnetic fields (23) rotated through pickup coils (24), generatin...
established VIC
System setup requires filling the water fuel cell, adjusting excitor plate distance/volume, connecting to the VIC, then tuning to the resonant characteristic of the total system by adjusting the pulse...
established VIC
Modulator inductor coils (9 and 12), made of resistive wire, act as DC current limiters during initial fuel cell charging; the low-Q resonant charging circuit of the fuel cell (10, 11) in series with...
established WFC
During transient startup, unidirectional diode (14) is non-conducting and isolates the water fuel cell from the high-voltage multiplying component (8), allowing the cell to take a positive charge duri...
established VIC
Terminal resistor (12), affixed on the ground side of the excitor array between bypass coil (9) and ground terminal (13), is composed of resistive wire wound in the same coil configuration as bypass c...
established WFC
Surrounding the voltage zone with an electrical insulator such as Teflon, plastic, or glass (item 20 of Fig 9D) seals the voltage gap, preventing electrical leakage to the water supply and allowing a...
established WFC
Chemical interaction and amp flow are minimized by using natural water with no more than 20 parts per million of any contaminants; the rule of thumb is not to increase electrical conductivity by addin...
established WFC
Stainless steel T304 is used for the excitor array because it does not oxidize when exposed to liberated hydrogen and oxygen in water with no voltage applied; lab certification tests show a decomposit...
established WFC
The pulse waveform from the bypass coil (9) is transferred to stainless steel excitor plates submerged in natural water; due to skin-effect, voltage zones of opposite polarity form across the plates,...
established VIC
The high-frequency voltage bypass coil (9), wound of resistive wire, duplicates the incoming voltage pulse train from the secondary coil (8) via inductive coupling: the pulse creates an oscillating ma...
established VIC
In the Voltage Intensifier Circuit transformer, the primary coil is copper wire and the secondary coil is resistive wire, both insulated to prevent shorting; the two coils are joined on the ground sid...
established VIC
Optocoupler (4), triggered by variable gate circuit (5), gates the pulse voltage frequency waveform on/off; the gated pulse train on-time (16) vs off-time (17) is adjustable from 1% to 100% duty cycle...
established VIC
Optocoupler (3), triggered by pulse frequency generator (2), attenuates power supply voltage (1) into a pulse voltage waveform (Fig 9A); varying the pulse generator's triggering rate from 1Hz to 1MHz...
established VIC
The first-stage variable power supply is any conventional AC-to-DC or DC (non-regulated) supply providing an adjustable output voltage range from less than one volt to 110 volts and up, used as the fi...
established VIC
Resonant Charging Choke (47), placed between the negative voltage zone (44) and electrical ground (48), helps maintain capacitance value (voltage level) within the Resonant Cavity during voltage pulsi...
established VIC
Distilled water is an insulator to amp flow; natural water with less than 20ppm of contaminates maintains a high dielectric constant, and the VIC's component arrangement retards or prevents amp flow.
established VIC
Capacitance formed between conductor plates 44/45 with natural water as the conducting medium is relatively high, and this capacitance opposes any change in circuit voltage, delaying voltage change un...
established VIC
Stainless Steel Material T304 forming voltage zone (45) does not chemically interact with liberated hydrogen, oxygen, and ambient air gases in natural water when exposed to a voltage potential during...
established VIC
High voltage output from Resonant Charging Choke (43) forms a Positive Electrical Voltage Pulse Potential across voltage surface area (45), which is immersed in natural water, per step-charging graph...
established VIC
Resonant Charging Choke (43) is a Modulator Inductor that sets up an oscillation at a given charging frequency (voltage pulsing rate) with the effective capacitance of a pulse-forming network to charg...
established VIC
Blocking Diode (14) conducts current in only one direction, preventing electron flow toward the Secondary Pickup Winding (42) during Positive Voltage Potential formation.
established VIC
The resistive wire-coil Secondary Pickup Winding (42) allows a voltage potential to form via electromagnetic induction, while its Ohm value acts as a resistor opposing electron flow from circuit elect...
established VIC
The circuit's purpose is to form opposite electrical voltage zones while restricting amp flow during the Electrical Polarization Process, which splits the water molecule by voltage stimulation rather...