Steve

Hi Hardkrome,

Your reaction was the same as mine, in the beginning. The way the dude talks doesnot give any confidence. But after really listening to him, explaining the coil capacitor voltage current story,  he made more sense to me.
You know, in the past, i used the power from the waterfuelcell to power the primary of my alternator.
That much power came of my cell.
But i never tried to hit the cell with Bemf pulses of high voltage and then trying to short the cell out with a bulb.....
Stan always stated that you can use the watercell as a source of electrons.......100kw he even mentioned once....

Just my thoughts

Quote from: Steve on March 18, 2018, 18:18:18 pm

. http://www.courtiestown.co.uk/electrolysers/dave-lawton/dave-lawton-pll-built-pcb.html Courtiestown in the UK no longer exists... So you can no longer buy any of the Dave Lawton Kits...

you can no longer buy these because Dave Lawton can no longer SELL these .   no one wants them , what for ?

Well, in case of an crisis, we always can make one or two.....

for me, it seems a bit wierd having a choke in parallel with the cell...

Hello Steve.
Where did you saw the 6w producing 8 LPM?

Hi Xblade,

Its written in his youtube profile.
On the ' about' tab. His last profile tab.


cheers

My drawing of what i understood of all available info.....
Any comments?

Thanks!!!!

Update:
My Circuit is just a Dave Lawtons Phase Locked Loop (PLL) Circuit with a 240 Volt Variac Transformer, a 600 Volt SDR943-61 rectifier, a H11D1 Optocoupler with a 100 Ohm 25W Resistor and a C38M SCR connected to a a 8XA Choke with a 1N1188 Blocking Diode. . Every cubic foot of water contains 1,376 cubic feet of Hydrogen & 680 cubic feet of Oxygen. 12Volts at 0.5Amps =6W(Watts) & produces 8 Liters of HHO/Minute. Stanley Meyer states WATER is 2.5 times more explosive than Petrol, so a V8 4.7 L/100 Kilometers requires only 1.88 L/100 K of WATER = 2,586.88 L of Hydrogen. 43.11 L Hydrogen/Minute = 33W. . http://www.courtiestown.co.uk/electrolysers/dave-lawton/dave-lawton-pll-built-pcb.html Courtiestown in the UK no longer exists... So you can no longer buy any of the Dave Lawton Kits...

He uses:
2 pieces in series of the http://www.pertronix.com/prod/ig/flame/coils/50000_volt.aspx

Its a long time ago that i seen such a great video!

aha.ok.
Two transformers on 1 core.
A isolation transformer with a secondairy after the secondairy....

so what did you do with the original secondairy coil?
Did you remove it from the vic?
Just use the two choke coils as secondairy, or wrap a bifilar coil and use it as a secondairy?
I am happy that you still try to uncover the vic, Brian!

I will give you a secret. The secret is if you remove the secondary high voltage coil you will be left with a isolation transformer that is center tapped because coil was removed. Now that is a very big secret all done on One core or else it will not work on separate cores. So basically what you have there is a isolation transformer but with a secondary intact is where the voltage is restricted or current or whatever it may be and there is some great change there there is some phenomenon as we know with the biffler and XYZ and the other antimatter coil. Be careful not to wrap your calls the wrong way or they could disappear. And reappear somewhere else.

Dont tell me that you are serious here....are you?

Thanks Brian for your reply.
I am thankfull that you share your current tests.
This topic is about me trying to understand the typical dave lawton circuit , that is acting in its way as it is.
For years, i thought i knew why it works, but i was so wrong.
I will make some drawings....That makes it a bit easier to understand.

Cheers!

I wanted to share my deapest thoughts on the VIC.
I re did a setup, like the one we all have tested many many many times.
Its the coil to wfc to fet and a diode for the back spike of the coil and cell.

I made some models trying to understand what and why this works.
I can create more amps going into the cell then i pull from the powersupply. Almost double.
X blade called it a buck converter.
But what is really happening?
Why did Hydrocars and me ran the alternator years ago with charging the rotorcoils with power of the wfc?
This is what is happening from my current perspective. Its a combi from Meyers EEC and what reseachers are telling about charging the wfc with radiant energy etc etc

I can make some drawings, but i try first like this:
The WFC works with 2 primary coils...........
Now its your turn to react on this statement.
Small hind: When the cell is running (so not the first second after starting up) the first primary is charged by the powersupply and the second primary will be charged by ............??

Please your reactions!

Steve

My life is a big mess at this time. I've been stuck in court case after case and depressed, it also seems like I can't ever keep my grass cut, phew! I can't wait to get back to this stuff. I will have to disassemble my own work to relearn how I even done it. It's all just a matter of time for me. I have one nasty x that will not stop papering me to death, and,,, it takes all of my money!!! However I've been going through this with her for 7 years now and I might add I think I have it beat this time! My last court date I hope is the 9th of this month.

i wish you all the luck, B....Hope the shit stops for you.

cheers!

it was my first replication....
Hydrocars advised the selfpowering rotor from the cell, after the cell was ongoing producing gas.
Still, the rotor needed the external motor to drive it....
Not sure what he means now with that extra coil and breaking the water....
Lets see

That was fun, hahaha.

I think that the real stuff from Meyer, was just the alternator setup.

Cheers

I have a friend to who Meyer did a demo with the alternator....
He reported to me that the wires to the cell from the alternator were HOT......

cheers

I think i have the most of the compenents now and also the pcb ;-)

In two weeks, it should be ready solderd

I agree.
I also will get two flamethower ignitioncoils...

The first parts have arrived!
Pcb will come in next week...

Good luck steve, the feedback circuit is almost the same on Meyer vic, but honestly I dont believe that anything "magic" will happen.

Cheers

I dont expect magic....The magic happens with an EEC and the deuterium gas and not with basic HHO....