Steve

Hi guys,

I want to share a video:


I am trying to combine all stuff that i know into one setup.
Not there yet.....

Merry Christmas!

or an external ampmeter.........
nothing goes for free

several hours laters....

Funny and not funny

The amp meter on the powersupply is showing at a certain frequency zero amps and when the frequency is off by a little, the amps go up.

Now i have put an external ampmeter in series and that is showing pulsed amps, even when the ampmeter at the powersupply says zero amps.

What is going on here?

I made a short video to show you my zero amp setup

Does anybody know who this guy is?
Hitby13kw

Regards
Steve

https://www.lenntech.com/stainless-steel-304.htm

Check that out, B

The EPG must have been his later work, is it?

Thanks Jim, again. Its an interesting topic.

I still have difficulty with the fact that Stan was using other gasses then the ones you can get out of water....

You simply create double the voltage.
With 20kv coils you get 40kv....
In the case of a Meyer, i might even decouple the secondairys, so you have a totally isolated secondairy circuit.
I know it is possible, but you have yo open the coil casings...
Its a bit of tinkering..

Nobody?

yes, i still cannot let it go.....

Here are two schematics that are additional to eachother.
I think that the toroid is getting its voltage of two ignitioncoils.
Then you get the tesla coil and the rest...

what you done there?

i kind of see this happening in the past but it was a cable that were not well contact with the electrode in my case..

Sometimes you connect info .......
watch from 39:10
Puharich pulsed slow ...2 a 3 seconds per pulse
To flip protons.

Its very intresting

well, i had the eec running.
A lightbulb was burning.
No special results to mention on that.

So i played a bit futher...
And then this happend..

If i find some time tomorrow, i will build the EEC part.
I think a P channel switch should be able to do that.
When the coil is charged, i also have to discharge the cell with the EEC circuit...however it will look like.
When the coil is discharging it self into the cell, the eec must be switched off.
It will be interesting to see if removing the charge of the cell, trully boost gas production...

Ok, this one was still on my to do list.
Here a picture of my testcell showing gas.
A note: it is charged, only by bemf.
I use the primary of an ignitioncoil.

i am not sure why the forum got in error, but i had to remove the last 3 posts of this topic...
Sorry guys. You have to re post again.
Its now working again.

cheers

Just to make point....2 pictures of my early work

Steve, our great Steve.

Yes, it hold a charge but below 2 Volts, above that electrolysis starts, and conductivity rises in a non-linear way.
I never experienced this BEMF from the cell, maybe because I dont use any electrolyte than the minerals and contaminants present in the natural water.

Aussepom welcome back and thank you for your input.

I am just an old man who used a tall tube cell with tap water....
No electrolytes, with a standard alternator.

Timeshell I am not so certain about that.

As I already said, I cant see the WFC acting as a capacitor or being reactive like a capacitor.
It looks to me like a load and nothing more.
Since it have the diode In-line it cant act another way than the DC resonant charging circuit.

Well, my 2 cents: the cell holds a charge. For that it is a capacitor/condensor.
The other cent: i posted many many lightyears ago a picture of the negative voltage peak produced by the cell when the dc was removed from it.
That negative pulse can be collected and re-used.
In the days, i used that pulse to charge the rotor of my alternator setup.....

For me, that negative bemf pulse of the cell was strong enough to charge a 5v/2a rotor coil.....
Use that pulse in a serie of parallel coil setup ala meyer....

now its getting intresting