andy

Hi Steve
Very interesing , can you give link to orginal source?
thank
andy

Hi Sebos
Here is circuit of Busi you want.
andy

What I quickly figured out was that I needed a variable plate cell to widen the gap so I could take the voltage up on the variac. But that didn't stop me, I jacked up the volts anyways. It still current limited itself, but the water started heating. (need bigger gap)

The interesting thing was that the tiny scr never even got warm. Quite bizarre I must say. You would never think it would work.





Hi Hard Krome.
What choke  and cell you used , and what voltage you reached when water started heating, tell please?
Thank for sharing and ansver.
andy

HI to All
In Sales manual page 55  resonant action Stan wrote about two oscillating voltage fields. ( First oscillating voltage field is formed around a second oscillating voltage field opposite in electrical polarity . Two oscillating voltage field are synchronized into a single repetitive wave form) What Stan mean by this two field one around a second?
Thank for Your ansver
andy

It eliminates the opposing magnetic field problem because on one layer the coils do not move move, just the secondary, then on the next layer the secondary stays still and the coils move, so you never have magnetic fields moving against each other - just the secondary moving relative to the coils, where the coils alternate between north south north south, so yes, it does do exactly as he says and eliminate a lot of problems with the conventional car alternator, and in particular it he designed it to be a "current limiting voltage source" with "power isolation" where a "pulsed input results in a pulsed output" and he even talks about it being used to control a car accelerator.

It's all right there, if you want to read it. This is a rotary vic.

HI Donaldwfc
Can you explain to my how to do coil alternator correctly to your words:
"It eliminates the opposing magnetic field problem because on one layer the coils do not move move, just the secondary, then on the next layer the secondary stays still and the coils move, so you never have magnetic fields moving against each other - just the secondary moving relative to the coils, where the coils alternate between north south north south"
I cant understand it . Thank for ansver.
andy

Wow, your the guy I need to talk to.  I am looking at doing an 8XA card setup.  I gather from your video you get something close to 1 lpm at the 5A setting?  Was this a 12v DC reading?  I run conventional electrolysis with electrolyte and get about that around 15A.  Ideally I would like about 2 lpm, but I don't want to run 30A thru my car electrical system.  I gather you need a coil in the setup.  Do you have a schematic?  Where can I get some of the details using the 8XA?  The 8XA takes 12v AC, correct?  Is that Tony's card you are using?

HI
Power input is 60V x 5A = 300W.
Power it in car can take 25A x 12V = 300W
andy

HI to All
Maybe someone here have more pictures about steam resonator for home heating unit like vic transformer , or other circuits boards? Maybe someone have picture of the other side circuit board posted by HMS-776? For figuring it out. Thank for sharing.

andy

Above you'll see the bridge rectifier circled in red, made of individual diodes.
I'm still not sure what purpose it serves through...The input to the rectifier is 24VAC...

HI
This bridge is the part of the power source for driving circuit of steam resonator for home heating. In the dune buggy power source is 12 V from accumulator. ( so bridge is for other purpose )
andy

Hi Seb,

I too cannot get my head around the diodes as you describe them.  How is the second diode connected again?  A picture would be helpful, much obliged.  I'm now running 8.5kv with my vic with little gas.

kb

Can you give the schematic of your circuit?
thank
andy

From 1 november 2011 I'm able to sent you all materials (including plan) for build that cell at popular price, in that way you save more time for find these on internet. Complete plan for Electron Cascade Cell is also available for personal usage at 50 euro with payment trough paypal. If you are interested sent me email to alnenc@libero.it. Regards Alessandro

P.S. Also Iontruster can buy these.. no problems

Hi Tutanka
Can now you sent all materials and plan for build that cell?
andy

Tony's site/download in Stanley Meyer Video Collection Torrent.
andy

Hi Spintronic
Primary coil must be made only one layer - correct? ( more layer in not allowed? what if  I want more turn of wire  but my spool is short? ) ?
Sorry for my english and mayby stupid question.
andy

Spintronic
By " single " You mean only one layer for the primary coil or can be more than one layer for primary but all loop in layer wound clockwise and wound with progresion (every next loop)  in one direction ( from left to right ) on the spool?
mayby You understand my corectly?
thank
andy

Spintronic
If I wound primary coil  for example in four layers on the spool must be every layer be wound from left to right ? ( left right , left right , left right , left  right ) or can it be wound : ( left right , right left , left right , right left ) and of course all wound clockwise?
Must this rule of wound  be in use for made the secondary and two choke coils?
thank for your ansver
andy

I'm from poland.
andy

Hi Tony
"Energy Pumping Action" page 125 as Stan describes is done via electric field no magnetic field.
andy

Spintronic many thank to You.

Tony
"  You have Parallel Resonance between L1 & L2. " is it true
or between L2 and the cell?
andy

Thank Spintronic
andy

HI Spintronic
Many thanks for sharing Your knowlege. My english is bad.
Can you clear this to my- only primary coil must be the iron wire , secondary and two resonant coils can be the copper wire , please?
I like learn from you.
thank
andy

HI Tony
You can use hand drill to wrap the coils. Simply attach your bobbin in head drill and run drill by hand.
andy