Bench
1,315 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established WFC
Under repeated pulsing, water confined between the capacitor plates takes on an electrical charge that increases via a step-charging phenomenon, with voltage continually increasing to about 1000 volts...
established VIC
The wiper arm on the second inductor tunes the circuit and accommodates to contaminants in the water so that charge is always properly applied to the water capacitor.
established VIC
The overall circuit is a 'resonant charging choke' circuit — an inductor in series with the water capacitor forming a resonant circuit — with such a resonant charging choke placed on each side of the...
established VIC
The stepped-up pulse enters a first inductor formed from 100 turns of 24 gauge wire, 1 inch in diameter, around which an electromagnetic field forms; when voltage switches off at pulse end, the field...
established VIC
The primary coil of the toroid is subjected to a 50% duty cycle pulse; the toroidal pulsing coil provides a voltage step-up from the pulse generator in excess of five times, with actual step-up ratio...
established VIC
A 1N1198 diode in the circuit acts as a blocking diode/switch allowing voltage flow in one direction only, so the capacitor is never subjected to reverse polarity; the diode also allows the inductor's...
established VIC
The step-up coil is formed on a toroidal core of compressed ferromagnetic powdered material (e.g. 'Ferramic Q6 Permag' powder), 1.50 inch in diameter and 0.25 inch thick, with a primary coil of 200 tu...
established WFC
Resonance in the circuit was achieved at a 26 volt applied pulse to the primary coil of the toroid at 10 kHz, causing water molecules to disassociate into elemental hydrogen and oxygen along with prev...
established WFC
The water capacitor of the fuel cell consisted of two concentric cylinders 4 inches long; the outside cylinder was 0.75 inch outside diameter, the inner cylinder was 0.5 inch outside diameter, with a...
established WFC
A preferred construction material for the capacitor plates of the water capacitor is stainless steel T-304, chosen because it is non-chemically reactive with water, hydrogen, or oxygen.
established MISC confidence 0.80
As shown in FIG. 7A and FIG. 7B, two directional gas valves are connected to the plates, leading to destabilization of the gas within the resonant cavity.
established MISC confidence 0.80
The gas circuit of FIG. 5B is interconnected at input 'A' to a concentric point 'A' of the pulsing circuit of FIG. 4, combining the hydrogen/oxygen input energy stage with the pulsed electrostatic fie...
established MISC
When one pulse train is switched 'ON', the other pulse train is switched 'OFF'; a blocking diode directs electron flow to the electrical load while a resistance wire prevents voltage leakage during th...
established MISC confidence 0.80
Gas waves are repeatedly subjected to the resonant cavity (shown in FIG. 4 as a coil) while providing thermal explosive energy, where one pulse ignites the gases and changes them to successively highe...
established MISC
The electron field voltage applied is approximately several thousand volts, which triggers the formation of positively charged ions without a polarity change; a potential of approximately several thou...
established MISC
The conductive plates of opposite electrical polarity used in the resonant cavity are preferably constructed of stainless steel T-304, chosen because it is noncorrosive and reactive with water, hydrog...
established WFC
Means for varying the physical spacing between the spatially positioned plate exciters are used to vary the rate of hydrogen/oxygen gas generation; this spacing variation is correlated with control of...
established WFC confidence 0.80
With multiple secondary windings on the rotating field, the number of output pulses equals the number of windings; pulse frequency depends on the rotational speed of the field, and the induced seconda...
established WFC confidence 0.80
When the input voltage is DC, it is converted to uni-polar d.c. voltage pulses using a rotating field with primary and secondary windings — the DC is connected to the primary winding, and a rectifier...
established WFC confidence 0.80
In a multi-plate configuration, positive potential is connected independently to each of one set of plates and negative potential independently to each of the other plates, with a resistive element co...
established WFC confidence 0.80
The resistive material sandwiched between the negative exciter plate pair comprises a resistive material combined with a binder; varying the percentage of binder varies the resistance of the material,...
established WFC
The exciter plate receiving negative voltage includes a ground connection and an electron-inhibiting resistive element (optionally variable) connected between the negative plate and ground to limit el...
established WFC
Means vary the amplitude of the uni-polar d.c. voltage duty cycle pulses to a minimum level sufficient to maintain resonance between the pair of plate exciters, while repetition frequency of the pulse...
established WFC
The pair of plate exciters are spatially positioned in the natural water with a physical distance between them equal to a wavelength corresponding to a particular frequency of the voltage's back-and-f...
established WFC confidence 0.80
The duty cycle of the uni-polar d.c. voltage pulses used to inhibit electron leakage can be varied periodically, aperiodically, or non-uniformly across a plurality of distinctive amplitude gradient le...
established WFC confidence 0.80
Means are provided to vary the amplitude of the duty cycle pulses and correlate their repetition rate with amplitude, producing an average pulse amplitude below the level that causes electron leakage,...
established WFC
A pulse forming circuit varies the duty cycle of the uni-polar d.c. voltage pulses to a predetermined repetition rate, inhibiting electron leakage as the amplitude of voltage applied to the plate exci...
established WFC confidence 0.80
The transformer in the AC-to-DC-pulse conversion circuit further includes variable inductive means for varying the output frequency of the voltage induced in the secondary winding, further inhibiting...
established WFC
The circuit for converting AC input voltage to uni-polar d.c. voltage pulses comprises a transformer having primary and secondary windings, with a rectifier circuit connected across the secondary wind...
established WFC confidence 0.80
When the AC input voltage's converted amplitude applied to the plate exciters is increased to a second level, the circuit further varies the frequency of the input AC voltage to further inhibit electr...