Bedini Energizer Kits Available!
Started by admin · · 107 posts · last reply 11 September 2015
-
#51 ·
I meant the Monopole Master class DVD:John_Koorn wrote:
bluestix,
No one is dodging any bullets here. That was a very short video of a small part of one of many test runs we did in John's shop at the time. It is very hard to look at a few minutes of video and draw any conclusions on what the charge/discharge ratio may be.
Our testing over repeated cycles showed that the charge battery charged at a similar rate as the primary battery discharged. If the mechanical energy generated by the rotating wheel was factored into the equations, the COP of the machine was greater than 1.
Can you post a reference to the advanced builders DVD where it shows the same thing? I'm not sure I've heard of it.
Thanks,
John K.
MONOPOLE MASTER-CLASS -
#52 ·
Tom C wrote:
The SG board that comes with the kit does not have neons in the circuit, so the answer is no. unless there are design changes I do not know about. there were no neons in the first prototypes we assembled.
Tom C
To AllComplete circuit board with all transistors, resistors, diodes, neon bulb protection, -
#53 ·
Geoffrey,
John will answer you about the circuit board later today sometime. -
#54 ·
@All,
We will be able to take orders again, but due to parts costs increase by the manufacturer of the plastic frame kit, the new retail price is posted here:
Bedini SSG Monopole Energizer Motor Kit
Here is the forum's order form: http://www.energyscienceforum.com/be...dinissgkit.pdf
Orders with that form will go straight to John Bedini's office.
Tesla Solar Chargers, LLC is his personal company - a few people have asked me who owns that company. -
#55 ·
Potted Boards
Geoffrey,
The neon was placed in the circuit to protect the 2n3055 transistor since it was a 60 volt device. If you exceed the 12 volt rating of the machine then you would use them. But I have changed the operation of the machine from repulsion to attraction based on mechanical findings. Everybody is free to build any circuit they want. I'm not going to pot anything in the kits. You are free to change anything at your own risk. I will post a circuit board layout and a picture of the board. Running the SSG in attraction mode does not require a heat sink on the output devices, it is only required in repulsion mode. The same circuit is used in the kit as what is in the SSG book. Most people do not want to spend time building things from scratch and just want to buy it already to assemble, and ready to run. As I said in the beginning you can find every variation of the SSG on the internet and none seem to get the results that I got with exception of a few people. My intent, was to get everybody on the same page with how the circuit works and what my testing consisted of. I only use a 1 amphr rate because if you cant do that then give up. So, In a simple answer to question about potted circuit boards and layout I will post it as soon as I have my circuit boards along with a circuit diagram for those that must change things.
John
geoffrey sr miller wrote:
To AllComplete circuit board with all transistors, resistors, diodes, neon bulb protection, -
#56 ·
John_Bedini wrote:
Geoffrey,
The neon was placed in the circuit to protect the 2n3055 transistor since it was a 60 volt device. If you exceed the 12 volt rating of the machine then you would use them. But I have changed the operation of the machine from repulsion to attraction based on mechanical findings. Everybody is free to build any circuit they want. I'm not going to pot anything in the kits. You are free to change anything at your own risk. I will post a circuit board layout and a picture of the board. Running the SSG in attraction mode does not require a heat sink on the output devices, it is only required in repulsion mode. The same circuit is used in the kit as what is in the SSG book. Most people do not want to spend time building things from scratch and just want to buy it already to assemble, and ready to run. As I said in the beginning you can find every variation of the SSG on the internet and none seem to get the results that I got with exception of a few people. My intent, was to get everybody on the same page with how the circuit works and what my testing consisted of. I only use a 1 amphr rate because if you cant do that then give up. So, In a simple answer to question about potted circuit boards and layout I will post it as soon as I have my circuit boards along with a circuit diagram for those that must change things.
John
Hi John
Thank You very much answering.
I know you are under a lot of stress.
I do not use neons because I know what to do with your technology, I was thinking of the less experience people.
I would like to talk, if you get a chance 215-910-1193
Thanks
Geoffrey -
#57 ·
Circut Board and Layout Board
Here is the circuit board from the Kit. The circuit layout you are looking through the board.
John
-
#58 ·
Had a few questions from some people that placed orders with the order form that had the original price before the price change.
If we receive payment and it is postmarked before yesterday's date, YES, we will honor the original price.
If you send in an order or wire payment from yesterday on, it needs to be at the new price indicated on the order form. -
#59 ·
The kit is great. I started building this using the instructions from the book. I have three friends that are also interested. So far we have three frames with wheels;fixed shafts being prepared by the machine shop. I ordered in the electronic components, magnets, wire. Is it possible to order from you spools ,puls cap comutator and caps so we can learn the effect of the entire circuit? Thanks for all your help. Jeff Joseph in Hilo Hawaii -
#60 ·
Hi Jeffrey,Jeffrey Joseph wrote:
The kit is great. I started building this using the instructions from the book. I have three friends that are also interested. So far we have three frames with wheels;fixed shafts being prepared by the machine shop. I ordered in the electronic components, magnets, wire. Is it possible to order from you spools ,puls cap comutator and caps so we can learn the effect of the entire circuit? Thanks for all your help. Jeff Joseph in Hilo Hawaii
It sounds like your Bedini SG is coming along well.
You can order spools, coil holders and welding rod from our website - Coils and Coil Components
John Bedini is just finalising the comparator cap pulser board and we should have this available to order in February.
John K. -
#61 ·
impeckable timing placed order last night. Thanks again Jeff -
#62 ·
HI John
Thanks for The circuit layout.
Are you going to get back into the crystal alum batteries?
Geoffrey
John_Bedini wrote:
Here is the circuit board from the Kit. The circuit layout you are looking through the board.
John
[ATTACH=CONFIG]1436[/ATTACH][ATTACH=CONFIG]1437[/ATTACH] -
#63 ·
I apologize for the inconvenience, but we will not be accepting any more orders until the current orders are filled. We are swamped with orders and do not want to get backlogged too much. I'll post a notice when they're available again. Thank you for your understanding. -
#64 ·
If you guys want some help with manufacturing I know some really good people. The time wasted doing it yourselves could be better spent doing research. The extra money could be used to hire more research staff.Aaron Murakami wrote:
I apologize for the inconvenience, but we will not be accepting any more orders until the current orders are filled. We are swamped with orders and do not want to get backlogged too much. I'll post a notice when they're available again. Thank you for your understanding. -
#65 ·
Hi Aaron & AllAaron Murakami wrote:
I apologize for the inconvenience, but we will not be accepting any more orders until the current orders are filled. We are swamped with orders and do not want to get backlogged too much. I'll post a notice when they're available again. Thank you for your understanding.
Has anyone received their NEW Plastic SSG unit yet?
If so, Have you done any tests on it?
And are you going to post any videos on it?
I thought that John B. was going to post a video on the New Plastic SSG unit with potted electronics
and some test Data about the unit?
It would be cool to see some Data on the new unit.
I have my owen data on my units and want to compare the data from the new unit.
I Also offered John B., that I can help him put together some product for him , but never herd back from him.
I have a full lab that can do anything, Just thought I will help.
You can reach me though this website www.energybat.com
Thanks ALL
Geoffrey -
#66 ·
Geoffrey,
There is absolutely no need to repeat yourself.
If you are wondering or thinking, "I just want to make sure someone sees it." The answer is - yes, we see everything and will reply to what we can when we can. -
#67 ·
There was a video posted on some preliminary tests - you can look at that for starters. Not sure where it is, but I saw John K. comment about it.geoffrey sr miller wrote:
I thought that John B. was going to post a video on the New Plastic SSG unit with potted electronics
and some test Data about the unit? -
#68 ·
Here it is:Aaron Murakami wrote:
There was a video posted on some preliminary tests - you can look at that for starters. Not sure where it is, but I saw John K. comment about it.
John K. -
#69 ·
Arron & AllAaron Murakami wrote:
Geoffrey,
There is absolutely no need to repeat yourself.
If you are wondering or thinking, "I just want to make sure someone sees it." The answer is - yes, we see everything and will reply to what we can when we can.
Sorry did not want to upset the apple cart, just wanted to know if anybody got the
New SSG unit and started to run some tests, Nobody has posted any test data from the new SSG unit yet.
When will you be able to take orders again?
If you are back up I am sure some people on this site will be able to help John B.
I thought you had the units BOX up and ready to ship out when people place an order, I hope it is not like Rick F. take
the money and build the unit, then ship it out , everybody saw how that business model work out.
Have the units started to ship out to any one yet?
I just want to know before I order, and not wait 2-3 mo. for the order to come in.
I have supported buying Products from Peter L, John B, Rick F and Aaron M.
I have seen the video , John B. said he would do more videos.
I am sure other people are waiting for the SSG unit too.
By the way Aaron your book is very GOOD!
Thanks and have a great day!
Geoffrey -
#70 ·
Hi ALL
Hi to anyone that ordered a New SSG unit.
Has anyone received there NEW plastic SSG unit yet from JohnB.???
And what do you think of it???
Thanks
Geoffrey -
#71 ·
No one has recieved a unit yet. I have run the prototypes for over a week, it performs exactly like my own unit I built myself. you dont need one Jeffrey, you can wind the coil, and make the circuit board, you can prototype a board from the image John uploaded. you have already shown us you have the ability. it will perform as well as one you get from John. it is nothing spectacular, its just a kit, a beautiful kit however. follow the instructions in the SG book you will have the same machine.
Tom C -
#72 ·
Hi TomTom C wrote:
No one has recieved a unit yet. I have run the prototypes for over a week, it performs exactly like my own unit I built myself. you dont need one Jeffrey, you can wind the coil, and make the circuit board, you can prototype a board from the image John uploaded. you have already shown us you have the ability. it will perform as well as one you get from John. it is nothing spectacular, its just a kit, a beautiful kit however. follow the instructions in the SG book you will have the same machine.
Tom C
I want to say what a great job John K, you and the other people behind the seen have done
with the 4 Trans. Board that I got.
Here is what I got in the mail. see pics.
and Here is what I e-Mailed John K.
Hi John K.
I want to say that you have written THE BEST assembly instructions and schematic diagram That I have seen in a long long time!
It IS the way I like to receive information.
I know how hard it is to do great work.
I will post a write up of your kit soon.
I do agree people will steal anything that they can not make for themselves, It is sad to say the less!
one day I hope to meet you in person.
PS: Tom I have built the SSG units, I just wanted to ask some ??? to other users about there units, I would ask John B. but he is MIA on the forum.
Wouldn't it be cool to see a self runner SSG unit running on one battery ---- Things to come.
Thank You
Geoffrey -
#73 ·
Tom C wrote:
No one has recieved a unit yet. I have run the prototypes for over a week, it performs exactly like my own unit I built myself. you dont need one Jeffrey, you can wind the coil, and make the circuit board, you can prototype a board from the image John uploaded. you have already shown us you have the ability. it will perform as well as one you get from John. it is nothing spectacular, its just a kit, a beautiful kit however. follow the instructions in the SG book you will have the same machine.
Tom C
Hi Tom
Have you shipped any of the $1,000 dollar NEW SSG units yet?
And when will John B. let people order the NEW unit again?,I would asked John but he is MIA.
The reason is I might have 5 people that might order the new unit , that is $5,000 dollars.
2 of them want to see how other people used them.
If it is a long time I may build them for them.
Is John B. ever coming back to this forum?, I am probably speaking for a lot of people on this website.
Have fun.
Geoffrey -
#74 ·
No i have not shipped any.geoffrey sr miller wrote:
Hi Tom
Have you shipped any of the $1,000 dollar NEW SSG units yet?
And when will John B. let people order the NEW unit again?,I would asked John but he is MIA.
The reason is I might have 5 people that might order the new unit , that is $5,000 dollars.
2 of them want to see how other people used them.
If it is a long time I may build them for them.
Is John B. ever coming back to this forum?, I am probably speaking for a lot of people on this website.
Have fun.
Geoffrey
Tom C -
#75 ·
Tom C wrote:
No i have not shipped any.
Tom C
HI Tom
why the wait? John B. said that people would not have to wait for the product like Rick F did with his products that he sold.
How many SSG have you sold?
John K. did a fantastic job sending out the 4 Trans. board!!!
I guess the SSG's were not built yet.
Do you know when you will ship yet.
I should not have to ask you these questions, they should be answered by John B.
I hope you are getting paid good money on the units for your time.
It is one thing to do research and Totally a different thing running a business, you CAN NOT serve two Masters.
I hope things are well for you.
where is John B. and Chuck H??? MIA.
Have fun!!!
Geoffrey