Bench
1,304 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established STEAM
Voltage Intensifier Circuit (70) is an exact duplicate of circuit (60), applying duty pulse (48) to a second Excitor Plate (69) on the opposite side of the same water molecule; together circuits (60)...
established WFC
Excitor Plate (61) is made of Stainless Steel T304 material to prevent chemical interaction or material oxidation with natural water.
established VIC
Blocking diode (58) prevents electrical shorting from occurring across pickup coil (56) during pulsing operations.
established VIC
Voltage potential (57) gates ON unidirectional diode (58), allowing the potential to pass through in-line charging Choke Coil (59) to Excitor Plate (61), forming positive voltage field (62); the choke...
established VIC
Pickup coil (56) is composed of resistive wire, restricting amp flow within the voltage intensifier circuit (60), per WFC Tech Brief Section 4 (Voltage Attenuation Circuit Design Specs).
established STEAM
As duty pulse (53) forms across primary coil (54), electromagnetic field (55) is produced and couples with pickup coil (56), forming voltage potential (57) across the pickup coil.
established STEAM
Gate circuit (32) varies or regulates the alternating duty pulse (53/48) applied to the Voltage Intensifier Switching Circuit (AA) up to one megahertz or more.
established STEAM
Variable gate circuit (32) is a two-state switch linked to optocouplers (51) and (52). As gate signal (H) nears low state, optocoupler (52) triggers power switch (Q5) forming unipolar voltage pulse (5...
established STEAM
The Steam Resonant Cavity produces superheated steam by applying pulsating voltage fields on opposite sides of a water molecule while restricting amp flow, using an alternate pulsing circuit (Q5/Q6) f...
established GASPROC
The Electron Extraction Process is maintained during gas flow-rate changes by varying trigger pulse (59) in direct relationship to applied voltage level (58); this process also prevents spark-ignition...
established GASPROC
To prevent electron oscillation/deflection during the Hydrogen Fracturing Process, the amp-consuming circuit (180) can connect directly to the Gas Resonant Cavity's positive voltage zone (45) through...
established GASPROC
The Electron Extractor Grid (51) is attached to an electrical circuit (180) allowing electron flow (56) to pass through wire (52) to an electrical load (53, e.g. a light bulb with resistive filament w...
established MISC
An Electron Extractor Grid (51) is positioned on top of and in spatial relationship to the Gas Resonant Cavity Structure (110) of the Hydrogen Gas Gun, per Figure 20YID/20JX, to capture electrons libe...
established MISC
Liberated, electrically charged and laser-primed combustible gas ions pass through the Optical Thermal Lens assembly, are expelled through a quenching circuit, and reflected through a thermal heat zon...
established confidence 0.80
Laser or photon energy (I) of a predetermined wavelength and pulse-intensity is exposed to and absorbed by the gas ions to help reach gas ionization, deflecting electrons to a higher orbital state; pu...
established WFC confidence 0.80
As ionized gases accumulate inside the Fuel Cell, the resulting electrical charging effect (G) can become greater than the applied voltage itself, further accelerating the Electrical Polarization Proc...
established WFC
Once voltage potential (F) reaches a threshold, exposed water molecules and liberated hydrogen/oxygen/air gases begin to ionize, destabilizing atoms; several thousands of volts trigger this ionization...
established WFC
At Analog Voltage Level (E), atom charge intensity increases enough to terminate covalent bonding between hydrogen and oxygen atoms; the liberated electron is attracted toward the hydrogen atom while...
established WFC
As Analog Voltage Level (D) approaches the millivolt range, the stationary water molecules elongate because the charged atoms are attracted toward opposite voltage zones, disrupting the mass equilibri...
established WFC
At Analog Voltage Level (C), oriented water molecules align end-to-end between the excitor plates in a linear direction; this occurs as voltage enters the microvolt range, after which molecular moveme...
established VIC confidence 0.80
Only several gigavolts (billionths of a volt) of applied power are needed to initiate molecular orientation; an amp restricting circuit (9XA, per Figure 20YD) allows this orientation process to occur...
established WFC
Because the water molecule's hydrogen atoms are positively charged and the oxygen atom is negatively charged, the applied analog voltage pulse causes random water molecules to spin and orient: hydroge...
established WFC
The analog voltage range (voltage intensity) applied across the excitor-plates is typically from zero to 5,000 volts and above, always positive relative to negative ground potential, with polarity rem...
established WFC
A unipolar Voltage Pulse Train is applied to the voltage intensifier assembly, forming an analog voltage pulse train that increases linearly from a low energy state to a high energy state across the e...
established
The Magnetic Spin Generator produces A.C. electrical output when the pickup coil-array is series-wrapped Right-Hand to Left-Hand, and D.C. output when wrapped in the same direction; orientation coils...
established
The permanently magnetized particles of gas prevent electromagnetic coupling between the orientation coils (12/13) and the pickup coils (2a...2n); instead, power input rotates/spins the gas particles...
established
To increase electrical power output, the non-magnetic tube (1a...1n) is spiral-wrapped through the pickup coil array (2a...2n), as shown in Figure 33, which increases the number of magnetic flux lines...
established
When the orientation coils (12/13) are de-energized, the permanently magnetized particles (16a...16n) rotate another 90 degrees, reforming field (4) while field (3) collapses; the collapsing field (3)...
established
When the variable gate circuit (EE) energizes both orientation coils (12/13) simultaneously, equal-magnitude fields (5/6) in North-South relation form across the air gap, terminating field (4) as the...
established
To permanently magnetize the gas particles (16) inside the tube (1), an electrical potential is applied across the pickup coils (2a...2n), forming electromagnetic field (4) that jumps the air gap (7);...