Some here are suggesting Stan used iron or other wire in his dunebuggy coil, and that ferrous wire is the only way to make the vic coils work. I believe you said he used copper for all of his dunebuggy coils. Could you clear up this confusion?
Our minds will deceive us and cannot be trusted. They have to be renewed with the Bible, as Stan found, in order for them to work at their highest capacity. Who would know best how to process the water molecule, other that the One who created it? Some of the things Stan got into just boggles the mind - he had to have help from a higher power. Christianity is different from all others in that it requires trust in what Jesus has done for us to get to heaven, whereas all others make the requirement on what WE can do. Obviously, none of us can be good enough to make it on our own - even if we tried our hardest!
Merry Christmas to everyone out there! I'm sure we will be receiving more clues on Stan's stuff as we continue the research...
What is confusing is the resonant cavity has the tubes wired in series - how was it possible to wire each tube to it's own vic - or was this cavity as a whole connected to one vic? This is hard to resolve, unless this is part of another system...
Yes, received. There is a lot of content. It puts a lot of 'guesses' to rest to actually see what was there. I do still have some questions though about the resonant cavity tube design. I don't understand what the upper and lower notches are for, since it is a solid center tube... Is this where the outer screw studs connect?
Re: the spreadsheet - I did receive it. That was a lot of work to create I'm sure
Who would know more about the water molecule that the one who created it? Genesis 1:1, 1:2 Stan had help from a much higher authority!
Another interesting part in Genesis 1:2: "And the earth was without form, and void; and darkness was upon the face of the deep. And the Spirit of God moved upon the face of the waters."
The hebrew word for moved, ra?chaph, Strongs #7363, has a meaning of "flutter, move, shake". It is interesting that water is being discussed, and shaking could mean vibrations, even shaking at a much more fundamental level. We know that all matter is vibrating to a certain degree. We also know that the same 'substance', energy, manifests in many different forms, light, heat, radio waves, etc, but it is the same energy. This is interesting, because Meyer also describes his belief that light energy coming into the atomic structure is what fuels processes. When an atom goes through his modifications, it releases a tremendous amount of energy as a result. Also, the fact that light returns the water molecules to their original state is even more intriguing. Interesting concepts to be sure...
This is true - Mr. Don has helped further this research by his generous offering to the group. I suggest anyone able and appreciative of his generosity to donate what they can to him also. This is literally a collection of much time and work, and the time alone is worth $$$, not to mention the content and it's potential! Especially now, with the craziness of traditional fossil fuels...
Yes, he was a genius. Also, in one of his videos, he mentions about elongating the water molecule, then later exposing the water molecule to sunlight revives it and returns it to it's normal state, allowing it to be captured from the exhaust and re-used!
Here is what I have, I am unsure if it is the final version or not... I have just begun construction - parts are enroute. (Diagram originally from Tony)
Thanks for the clarification. What can I say, the circuit works beautifully as promised! Excellent production at .5 amp... more output than 'brute force' electrolysis cells at 10 amps! I still need to measure the coil inductance - just to be thorough. Now on to deeper Meyer truths, resonant scanning, steam resonators, etc...
Thanks Shadow - To avoid cluttering this board with off-topic info (this is a replication and not original Stan Meyer documents), I have posted my replication here: http://www.ionizationx.com/index.php?topic=1976.0
Do you have any clarification on the amp inhibiting resonant charging chokes in the 8XA box? How was this wrapped - each row by itself? I do not understand what is meant by 'row'. Basically, it is two physical wires being wound at the same time, correct? Thanks for any more info on this...
Thanks again - I understand the layout now. Undoubtedly this helps to get the maximum effect and interaction with the water. The two studs are connected to the ends of the pipes? I assume Stan used one of the slot areas to attach to the inner rod. Thanks again for all the feedback. We are getting closer.
No, it is currently being used on vehicles to supplement fuel which results in improved mileage (MPG). The circuit is capable of running a car on HHO alone if more cells were added, but this is not what it was designed for. Stan's next circuit, the resonant driver circuit, is what was used to run the dunebuggy - on water alone.
No they do not, but Stan used a Redi-line inverter for the early prototype of the dunebuggy. We have pictures of that. The 8xa was not designed to run on a 12V source (in a car), but was designed for the patent office to demonstrate the electrical polarization process on Stan's plate cell. Stan's original box ran on 120V AC (standard US household voltage). It can, be used in a car if an inverter is used. I have seen this done numerous times successfully...
Yes, the circuit uses 120V AC which is processed through the powerstat and a 12V transformer which powers the signal generator circuit. It can be used in a vehicle using an AC inverter (12V to 120V). The box WAS originally designed by Stan for plate cells, but we used tubes because they are more efficient and available...
Thanks Ali, I guess the source was lost in a quote of a quote of a quote - Thanks for the new info - I'm sure lots of people will find the acceleration parts especially interesting... I'm still waiting on parts before embarking into that area...
