HurstOlds

Did you ever get your 427 Cobra built?
 
Have you thought about running it on Hydrogen?    Not sure if you have seen this before, but I just had to show it to you!
 
427 Cobra run on Hydrogen:
http://www.clean-air.org/Hydrogen%20Cobra%20Story/Hydrogen%20Cobra.htm

Your post sounds like Timothy Leary from Tool's song
 

Think for yourself,  Question authority

Throughout human history, as our species has faced the frightening,
terrorizing fact that we do not know who we are, or where we are going in
this ocean of chaos, it has been the authorities, the political, the
religious, the educational authorities who attempted to comfort us by
giving us order, rules, regulations, informing, forming in our minds their
view of reality. To think for yourself you must question authority and
learn how to put yourself in a state of vulnerable, open-mindedness;
chaotic, confused, vulnerability to inform yourself.

Think for yourself, Question authority.

Good stuff

What you guys are saying is very interesting.  It appears much of it is founded in Hermeticism.  Besides, pretty all modern religions are rooted in the Hermetic teachings.  For those that don't believe that science and religion are related, I suggest that you look into the Hermetic Principles a little.  You may be surprised at how modern science is finally proving these age-old principles.
 
If you have a few minutes, check out the free book called The Kybalion.  You can get it free via Google Books (download as pdf, epub, or read online).  The book was written in 1908, so it's now in the public domain (free).
 
Quote from the book:

"when the pupil is ready to receive the truth, then will this little book come to him, or her.  Such is The Law.  The Hermetic Principle of Cause and Effect, in its aspect of The Law of Attraction, will bring lips and ear together - pupil and book in company."

This book connects with each person in different ways.  I thought it spoke to me about Stan's technology.
 
The Hermetic Principles:

I THE PRINCIPLE OF MENTALISM.
II THE PRINCIPLE OF CORRESPONDENCE
III THE PRINCIPLE OF VIBRATION.
IV THE PRINCIPLE OF POLARITY.
V THE PRINCIPLE OF RHYTHM.
VI THE PRINCIPLE OF CAUSE AND EFFECT.
VII THE PRINCIPLE OF GENDER.
 
I don't have a problem with religion.  My only problem is when a person only studies one religion, and then proceeds to fight tooth and nail for that one religion.  Expand you horizons, study more than one, and you'll realize they are all giving the same messages.....

Did you see @ 3:39, when he connected the primary coil....only one lead on the LED light bulb but it looks like it lit up a little....
 
Is that pulling power from the air or whatever, kind of like an exciter circuit?

I'm trying to figure out why this patent differs from Puharich's work.  It seems like Puharich was dead set on trying to achieve 8 hertz.  He talked about how healers produced 8 hertz in their hands, and could charge up water with that.
 
Some of the statements between the patent and Puharich coincide.  For instance, here's a quote from Puharich's unpublished book, page 123:
 

 ....and proved that a certain ELF frequency (3.21 hz) will cause cancer.  I have  repeated these experiments, and found this to be true. 
 
......
 
Note that a powerful carcinogen, ethylene dioxide, has coupling constants around 3 to 5 hz.  Note that another powerful carcinogen, formaldehyde, has a coupling constant around 41 hz.  Parish, et al, have found that the spin-spin coupling constants for water in malignant brain tumors (in humans and dogs) to rang from 4.8 hz to 13.4 hz, whereas normal brain gray matter ranges from 8.6 to 11.3 hz.  Thus malignancy shows a spread of frequencies from low to high ELF range  ie...with respect to normal brain EEG's, and carcinogens have a wide spread from 3 hz to 41 hz around the center frequency for normalcy of 8 hz.  However a single ELF frequency can roduce cancer.

So was this guy measuring differently than Puharich, and thats why the difference (4.55 to 8 hz)?
 
Maybe I need to study harmonics better.  I don't understand like when Puharich was talking about the 7th harmonic of 0.125 hz (= 8 hz)....

Thank you!
 
Anyone have a low frequency generator and want to play around with this?  Puharich mentions how healers were able to resonate water, and the water would hold it for days/weeks.
 
Many believe the Egyptians were doing stuff like this with water, the pyramids and their obelisks.  Many megalithic sites are built near water, on top of water, etc...
 
I also heard that Tesla chose his power stations to be near natural aquifers or water or whatnot.....

That is an interesting patent, kind of rides on the stuff that Puharich mentioned in his unpublished book.  I'm having trouble following the frequency calculations.
 
Anyone care to post up how to derive the calculation?
 
Example from patent: 24/3*2^17 hour = 4.55 hz
 
I tried doing [24/(3.2^17)]/3600, and it's not close.  Not sure what notation the equation is using.
 
Must be some sort of harmonic calculation or something that I am not understanding

While I like all of your thoughts, I don't really thing Stan's diagrams are all that complicated for building these circuits.  Yes, the VIC and more advanced stuff is, but I'm just trying to start from the beginning.
 
I need some help trying to figure out what components to use for each part of the circuit.  I'm kind of looking for someone that has 'been there and done that' to point me in the right direction.
 

 What I dont like about the 8xa drawing design is it shows a reliance upon a distributed mains supply to drive it and for it to function through the SCR to provide a "unipolar waveform voltage"that is switched at a timed interval.

Sure that design means people who are not electronics engineers or educated technicians may need to study electronics to work out what a SCR does blah blah blah however to my mind this makes the design less practical and less flexible in its design to be utilised in a vehicles power supply, thus my thoughts are:
 - a circuit design needs to be designed and built with the end result of it being used and mounted to a vehicle or other engine

I'm not sure, but looking over this circuit, looks like it was designed to be run in a car.  Look it over again....
A car alternator gives out 110 volts.  Instead of needing the Powerstat 21 to vary power delivery, you would just vary the speed of the alternator...
 
Also, that may explain why a voltage regulator (5 & 12 volt) is part of the circuit. I'm guessing that 9XD portion of the circuit is needed to drive the chips with 5 volts and possibly all other car electronics via 12 volts.
 
I may be way off on all this, but I still want to build the circuit in order to experiment and see what it has to offer.  Most likely it will just be a learning experience, or stepping stone onto bigger better things.
 
Now if I could just get some more comments answering my questions in my posts....
 
Thanks for the help guys

In regards to the actual 8XA circuit, I'm having problems trying to find part numbers listed on DynoDon's schematic.
 
Full bridge rectifier = MB12A2 5V 40
Clarostat vp-25-k
 
The Clarostat is listed as obsolete.  It looks like an adjustable wire wound resistor or something.  Can I just use a pot?  I'm not even sure what this is, any help?
 
Before posting, I think I figured out the bridge rectifier.  Looks like a 400v 25a.  I still can't find anyone that sells it, so might have to substitute something else in.
 
For the choke, is there only ONE choke in this circuit?  Can I just wrap the wires around a ferrite rod?  It looks like the EC52 is a 'E' shaped core.  Not sure if I can get those anymore, I don't know where to buy anything like that.
 
From my understanding, there's just two wires that are wrapped bifilar on one core?  What does the diagram mean when it says 760uH per coil?  Isn't there only ONE coil?  Is that if you were trying to run a multiple tube setup or something?  Each would need it's own coil?
 
Last question, near bottom right of diagram, the ground says TO BRIDGE.  Does this just connect the ground connection on the bridge rectifier?
 
Also, can I just use 18 gauge magnet wire for the choke?
 
I already picked up a Powerstat 21 for cheap.  I'm looking to order the rest of the stuff soon.  Any help would be appreciated.  Sorry for such long posts....

In regards to the 9XB circuit, I have many questions.  First off, what watt rating do you recommend for all of the resistors and pots?  I don't know how to calculate this....I know input power is 12 or 5 volts, and the rating of the resistor, but I don't know how much current this circuit uses. I would just guess 1/4 watt or something basic?
 
Also, the .01 uF capacitor, what voltage rating would that be?  Would it have to be anything above 12 volts because that is what is feeding the circuit?
 
Above each of the decade counters, the diagram shows "in/10".  What does that mean?  Does that just indicate that whatever the 555 or input gives it, it will divide that by 10?
 
I am planning on bread boarding these circuits, so a lot of this I think I will learn when I test it out, I mainly need to know what to choose for resistor/cap values
 
Thanks again

OK, here's my specific questions about the 9XD circuit.
 
The power transformer doesn't look like it's variable, so I'm guessing I can use any 12 volt power supply, capable of up to 3 amps?  Old PC power supply? 
 
Or could I just use an old PC power supply to get 5 & 12 volts directly, bypassing the need to build the 9XD altogether?
 
Suppose I did want to build the 9XD, what is the value for capacitor C4.  Diagram DynoDon posted says .33mF, but what voltage?
 
Also, is .33mF the same as .33uF when buying capacitors?
 
I think I could fabricate this circuit myself, I have a little experience soldering and making basic circuits.
 
Thank you

Hello everyone,
 
I'm new to all of this Stan Meyer stuff and I have been studying/reading/watching whatever material I can get my hands on.  My personal problem has been a lack of information.  Everytime I think I have all the patents or I have seen all of the videos, a new set of stuff pops up.
 
It's getting hard to keep all this stuff straight, especially when it appears Stan had many variations or evolutions of his ideas.
 
I want to get started on the basics and need a little help.  I'm trying to figure out where to start.  I saw TonyWoodside and a couple other people recommend starting with the 8XA circuit first, before getting into the more advanced stuff.
 
My first question is, was the 8XA circuit used for the WFC that had the adjustable plates?  I know these are very basic questions, but I want to make sure I have everything understood correctly.

<picture of variable plate cell attached below> SMVUS003.png
 
I saw the pictures that DynoDon posted here:
http://www.ionizationx.com/index.php/topic,844.msg13442.html#msg13442
 
This is exactly what I want to build.  I did see that StanMeyerLives built this setup and it looks like it worked.  Here is his thread:
http://www.ionizationx.com/index.php/topic,1976.0.html
 
I want to build something like this but I have some questions about what parts to use.  I posted in StanMeyerLives thread but there was no response.  I sent him an email through the message board and also a PM and no response.  I even registered at his website stansdream.com but my account is waiting for activation or something, so I can’t post in his thread over there…..
 
I was hoping you guys can help me figure out what I need to build this setup.  First off, is this essentially the circuit that is in the video “It runs on water”?  It looks like it, a couple knobs, a couple meters, etc…  just wanted to ask, because that video he has the tube set instead of variable plates. 
 
Ok, in regards to the 8XA circuit, is there any existing threads with part numbers to build this thing?  I’m going off of DynoDon’s pictures (http://www.ionizationx.com/index.php/topic,844.msg13442.html#msg13442) and I can’t figure out what some of the part numbers are.
 
The 8XA looks like it’s actually three circuits. 
1. PC9XD circuit for voltage regulation
2. PC9XB for handling pulse width
3. 8XA that uses the above two sub-circuits within it.
 
OK, so my initial question is, does the PC9XD circuit just provide 5 & 12 volt power for anything that needs that in the larger circuit?  Ie, the IC chips in the PC9XB card and stuff like that?
 
So those are my initial questions, I’ll make circuit specific questions in follow up posts.