Bench
383 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
A completely separate Voltage Intensifier VIC-Coil Assembly (1003) is periodically switched on by alternate voltage pulse waveform (T4B) once T4A terminates for a brief period (T3A), redirecting the b...
established VIC
Voltage intensity at zones (952/953) is directly determined by the number of turns of each coil (957/958) relative to the applied voltage amplitude of the incoming pulse waveform (...xxx Vn).
established VIC
The distributed capacitance (Cda...Cdn) of each coil experiencing inductance coupling (619) elevates the applied voltage level (Vn) to a higher amplitude, increasing voltage intensity needed to deflec...
established VIC
The simultaneous formation of positive voltage field (952) and negative voltage field (953) results from mutual electromagnetic inductance coupling between the two bifilar wrapped coils (957/56-958/62...
established VIC
Both primary coil (957) and secondary coil (958) forming the voltage intensifier circuit (990) are bifilar wrapped in equal length, causing both water molecules to be displaced at the same velocity si...
established VIC
Simultaneously, stationary negative voltage field (958) at plate (953) attracts the positive hydrogen atom of a separate water molecule via R-R' attraction, displacing it in linear movement at the sam...
established VIC
Incoming programmable gated pulse-frequency waveform (T4A) electrically energizes primary input coil (957), producing positive voltage field (952) across voltage zone (E13), which deflects the negativ...
established VIC
The VIC Switchover Circuit (1010) prevents amp influxing into and away from the periodically spaced negative voltage zones (E13-E14, E15-E16), while allowing opposite-polarity voltage potentials to de...
established VIC
When the Voltage Intensifier Circuit (VIC Circuit, Fig 10-1) is electrically connected to Voltage Zones (66/E11–67/E12), it establishes the functional parameters of the Optical Thermal Lens (Fig 10-2)...
established VIC
The Amp Inhibiting Circuit (970, Figure 10-1) restricts/inhibits amp flow to a minimal level while elevating the Difference of Potential (electrical stress) to the highest possible level, since greate...
established VIC
In all cases, the bifilar coils (56/62 and SS56/62) are electromagnetically orientated in the same direction.
established VIC confidence 0.80
The mutual inductance coil-field (Rp1+Rp2) causes coil capacitance (Cda...Cdn) to help maintain and increase pulse voltage amplitude, while the resistive value (Rs2) of the SS Coil-Wire further resist...
established VIC
Magnet coil-wire length is generally longer than the Stainless Steel coil-wire length, and the magnet bifilar-coil (56/62) is placed on top of the Stainless Steel bifilar-coil (SS56/62) to maximize mu...
established VIC
The magnet Coil-Wire (56/62) is best suited for voltage inducement, while the inductance/capacitance/resistance properties of Stainless Steel coil-wire (SS56-SS62) restrict electron movement beyond ea...
established VIC
Coil Stages (56/62a...56/62n + SS56/62a...SS56/62n) added/stacked sequentially into a single overall coil-array assembly (990A/B, Figure 10-3) form the Amp Inhibiting Network (970, Figure 10-1), herei...
established VIC
The Stainless Steel bifilar Coil-Stage Assembly (SS56/62a...SS56/62n) is electrically placed between the Magnet Coil-Stage Assembly (56/62a...56/62n) and the Water Gap (Cp) to obtain the optimum Volta...
established VIC
Stainless Steel composite coil-wire (430F/FR) has both inductance and resistive properties, typically 0.0048 ohms per foot, which combined aids amp restriction beyond what copper self-inductance magne...
established VIC
As additional Dual Choke Coils (56/62 + SS56/62) are stacked into the coil-array forming the Voltage Intensifier Circuit (970, Figure 10-1), amp-surge is kept to a minimal level while Voltage Potentia...
established VIC
Increasing the number of Resonant Charging Choke Stages (56/62 + SS56/62) added in sequential order increases energy yield, since the Multi-Coil Magnet bifilar coils are serially connected to an equal...
established VIC
Resonant Charging Choke Stages (56/62a...56/62n + SS56/62a...SS56/62n) are electrically connected in sequential order and magnetically linked by an Inductance Coupling field, producing the opposite-po...
established VIC
The programmable pulse-frequency (49a...49n, Fig 10-1) input is adjusted to tune-in to the dielectric property of the Water Molecule, enabling the Amp Inhibiting Circuit's Electrical Polarization Proc...
established VIC
Blocking Diode (52, Fig 4-9/1-1) allows the unipolar pulse-wave to go more positive on each pulse cycle by preventing the Resonant Cavity (Cp) from discharging during pulse off-time (Fig 1-4, 60 of Fi...
established VIC
The resultant voltage enhancement (Voltage Amplitude) of the VIC can exceed 40 kilovolts, instantly converting water droplets into thermal explosive energy on demand (Fig 10-1).
established VIC
Pulse-Voltage repetition rate sets up a step-up charging effect (Fig 1-3) since the Resonant Cavity (Cp) functions as a Capacitor (ER) due to the dielectric value of the liquid (or gases) contained, w...
established VIC
The paired coil-wires' opposite voltage potentials (positive attraction force B+, negative attraction force B-), referred to as Electrical Stress (SS'-RR'), are always equal in electrical magnitude/in...
established VIC
Beyond amp restriction, the paired spiral-wrapped Resonant Charging Chokes (56/62) cause voltage level enhancement beyond applied voltage input, as the Distributed Capacitance (C1a...C1n, C2a...C2n) a...
established VIC
The VIC Bifilar Wrap Coil-Assembly (Fig 10-3B) and VIC Dual Coil Wrap-Assembly (Fig 10-3A) both utilize 'E', 'I', and 'U' inductance core configurations to concentrate Mutual Inductance Fields (Rp1/Rp...
established VIC
To reduce amp leakage further, the copper wire of both Resonant Charging Chokes (56/62) can be replaced with magnetically inductive stainless steel wire (430F/FR), which has a resistive value (Ohms) t...
established VIC
The length and diameter of the copper-wire spiral-wrapped coil pair (56/62, Fig 10-1), combined with the applied Voltage Pulse-Frequency, determines how much amp leakage occurs across the capacitor Ga...
established VIC
The mutual inductance field between paired chokes 56/62 prevents amp in-fluxing (discouraging electron arc-over) across the Dielectric Capacitor Gap (ER)(66/67) while Electrical Stress of opposite vol...