Bench
1,304 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
As additional Dual Choke Coils (56/62 + SS56/62) are stacked into the coil-array forming the Voltage Intensifier Circuit (970, Figure 10-1), amp-surge is kept to a minimal level while Voltage Potentia...
established VIC
Increasing the number of Resonant Charging Choke Stages (56/62 + SS56/62) added in sequential order increases energy yield, since the Multi-Coil Magnet bifilar coils are serially connected to an equal...
established WFC
The greater the Electrical Stress (RU-RU' to ST-ST') applied, the greater the amount of thermal explosive energy released from the Resonant Water Gap (Cp), as shown in Figure 4-5 and Figure 10-1.
established WFC
Ever-increasing pulsating opposite electrical voltage fields with superimposed Rippling Voltage-Surfaces create a rubberbanding Pulsating Opposite Electrical Stress across the Water Gap (Cp), causing...
established VIC
Resonant Charging Choke Stages (56/62a...56/62n + SS56/62a...SS56/62n) are electrically connected in sequential order and magnetically linked by an Inductance Coupling field, producing the opposite-po...
established WFC confidence 0.80
The Dynamic Electrical Charging Effect (612, Fig 8-1) acts as a progressive Energy Priming Stage (500, Fig 5-1) when Static State Space (790, Fig 8-3) is configured to Dynamic State Space (800, Fig 8-...
established VIC
The programmable pulse-frequency (49a...49n, Fig 10-1) input is adjusted to tune-in to the dielectric property of the Water Molecule, enabling the Amp Inhibiting Circuit's Electrical Polarization Proc...
established VIC
Blocking Diode (52, Fig 4-9/1-1) allows the unipolar pulse-wave to go more positive on each pulse cycle by preventing the Resonant Cavity (Cp) from discharging during pulse off-time (Fig 1-4, 60 of Fi...
established VIC
The resultant voltage enhancement (Voltage Amplitude) of the VIC can exceed 40 kilovolts, instantly converting water droplets into thermal explosive energy on demand (Fig 10-1).
established VIC
Pulse-Voltage repetition rate sets up a step-up charging effect (Fig 1-3) since the Resonant Cavity (Cp) functions as a Capacitor (ER) due to the dielectric value of the liquid (or gases) contained, w...
established VIC
The paired coil-wires' opposite voltage potentials (positive attraction force B+, negative attraction force B-), referred to as Electrical Stress (SS'-RR'), are always equal in electrical magnitude/in...
established VIC
Beyond amp restriction, the paired spiral-wrapped Resonant Charging Chokes (56/62) cause voltage level enhancement beyond applied voltage input, as the Distributed Capacitance (C1a...C1n, C2a...C2n) a...
established VIC
The VIC Bifilar Wrap Coil-Assembly (Fig 10-3B) and VIC Dual Coil Wrap-Assembly (Fig 10-3A) both utilize 'E', 'I', and 'U' inductance core configurations to concentrate Mutual Inductance Fields (Rp1/Rp...
established VIC
To reduce amp leakage further, the copper wire of both Resonant Charging Chokes (56/62) can be replaced with magnetically inductive stainless steel wire (430F/FR), which has a resistive value (Ohms) t...
established VIC
The length and diameter of the copper-wire spiral-wrapped coil pair (56/62, Fig 10-1), combined with the applied Voltage Pulse-Frequency, determines how much amp leakage occurs across the capacitor Ga...
established VIC
The mutual inductance field between paired chokes 56/62 prevents amp in-fluxing (discouraging electron arc-over) across the Dielectric Capacitor Gap (ER)(66/67) while Electrical Stress of opposite vol...
established VIC
The energized Resonant Charging Choke (56, Fig 7-1/10-1), driven by input voltage pulses (49a...49n), creates an electromagnetic coupling field (Rp1) via self-inductance (640, Fig 7-3B) that crosses t...
established VIC
The Amp Inhibiting Circuit (970, Fig 10-1; 690, Fig 7-8) is composed of two copper wires bifilar wound about a magnetic induction core, restricting amp (current) leakage while encouraging voltage pote...
established
A typical 325 hp diesel internal combustion truck-engine would require about 48.1 microliters (μl) of a water droplet per injection cycle to accomplish the same open road performance as the 1600cc VW...
established
Under dynamic pressure of compression, approximately 7.4 microliters (μl) of water droplet volume per injection cycle is required to run the Dune Buggy 1600cc 50hp VW internal combustion engine at 65...
established WFC
Less water contaminants nets even higher energy-yield (gtnta through 85a-85h to gtntn), as illustrated in Water Chart (760) of Figure 7-15.
established VIC
Pulse Off-time (T2, Figure 7-8, related to item 620 of Figure 7-1) is adjusted to compensate for the rise and fall of the magnetic coupling field (71), producing applied Unipolar Wave-forms (64a throu...
established WFC confidence 0.80
Increasing Thermal Explosive Energy-yield (gtnt) to higher energy-levels (gtnta through gtntn) beyond the applied excitation voltage (Vn) is achieved by altering Voltage Surfaces (35b/35c) relative to...
established VIC
Voltage Compressional Wave-form (35b) and Expanding Voltage Waveform (35c) increase the intensity of applied pulsating opposite electrical attraction force (SS'-RR'a through SS'-RR'n) further during e...
established WFC
The operational parameter is to utilize Opposite Electrical Attraction Force (SS' - RR') at high voltage intensity (Vn) to instantly release Thermal Explosive Energy (gtnt) from natural water.
established VIC
The mode-of-operability of the VIC Coil Assembly (580, Figure 6-1) allows Voltage Potential (Vn) of opposite voltage polarity (66/SS' - 67/RR') to increase and be attenuated up to and beyond 20 kilovo...
established VIC confidence 0.80
The VIC circuit topology includes a Primary Coil (26) and a Secondary Coil (52), between which electrical power is transferred and maximized via the coil switching mechanism.
established VIC
Switching the member of Secondary Coil-Array (505a–505n) maximizes electrical power transfer from Primary Coil (26) to Secondary Coil (52) by keeping the Voltage Amplitude of the Pulse-train (49a–49n,...
established VIC
The Taper Resonant Voltage surfaces (E9/10) of Figure 6-2 act and perform as a 'Voltage Amplifier' when the Compressional Wave-form (B) of Figure 7-12 is intensified at Exit Port (32) of Figure 6-2.
established VIC
Voltage levels of variance (Va–Vn) are achieved by switching-in or switching-out members of the Secondary Coil-cavities (505a–505n), shown at 740 of Figure 7-13, in direct relationship to the Taper Re...