Somender Sigh grooves in cylinder head
Started by vzon17 · · 3 posts · last reply 5 February 2013
-
#1 ·
Somender Singh has been awarded an US Patent for his discovery of how to gain more engine power and economy by utilizing a small groove cut into the squish area(s) of the typical Internal Combustion Engine (ICE). The Groove(s) allows gasses to expand and compress with a quality that has consistently improved fuel efficiency, lowered operating temperature, improved torque and max power as well as lowering idle speed significantly.
Just an intersting little modification I plan on doing on my car. 1966 chevy biscayne with 6 cylinder.
I am rebuilding a 6 cylinder 250 chevy engine which will have multiple technologies to improve mileage.
1 - most moving engine parts coated with tungsten disulfide.
2 - Singh groove machined into head.
3 - swirl grooves put inside intake manifold.
4 - PCV bypassing engine vacuum
5 - HHO fuel catalysing for shortened burn time.
6 - Plama Igniton
7 - vapor generator for improved mileage, vaporizes fuel at cold temp
8 - High compression pistons
9 - steam injection...water injection to replace part of fuel
10 - exhaust scavenger that goes on end of tail pipe V-diode MPG Enhancer
11 - all the little tweaks and adjustments outlined in the Eagle research books on mileage improvement DIY energy saving methods and devices
Like the carburetor enhancer, the hyco and the hyzor running off separate alternator to produce actual browns gas.
12 - Aerodynamic changes to car including blocking radiator, and using turbulator tape and vortex generators on various body edges
13 - Use of friction reducing lubricant additives in engine, transmission and rear end and axle bearings. With an eye toward the Diamond lube system.
14 - top cylinder oiler.
Goal is to have a large size car that gets 50 plus MPG -
#2 ·
I experiment with this a lot. Every engine is different; with SBC race engines my current thinking is 0.050” piston to head at assembly is ideal. I learn something every day so this is subject to change.
Reducing the squish clearance enhances turbulence intensity; this reduces detonation tendencies to a point. The down side of ultra tight squish clearance is increased crevice space; these shadowed areas can lead to detonation. As with everything it’s a trade off. Get the squish clearance tight enough to enhance turbulence but not so tight that it creates areas of unburned mixture.
And of course we haven’t mentioned squish to bore ratio! -
#3 ·
some things you may want to add..vzon17 wrote:
Somender Singh has been awarded an US Patent for his discovery of how to gain more engine power and economy by utilizing a small groove cut into the squish area(s) of the typical Internal Combustion Engine (ICE). The Groove(s) allows gasses to expand and compress with a quality that has consistently improved fuel efficiency, lowered operating temperature, improved torque and max power as well as lowering idle speed significantly.
Just an intersting little modification I plan on doing on my car. 1966 chevy biscayne with 6 cylinder.
I am rebuilding a 6 cylinder 250 chevy engine which will have multiple technologies to improve mileage.
1 - most moving engine parts coated with tungsten disulfide.
2 - Singh groove machined into head.
3 - swirl grooves put inside intake manifold.
4 - PCV bypassing engine vacuum
5 - HHO fuel catalysing for shortened burn time.
6 - Plama Igniton
7 - vapor generator for improved mileage, vaporizes fuel at cold temp
8 - High compression pistons
9 - steam injection...water injection to replace part of fuel
10 - exhaust scavenger that goes on end of tail pipe V-diode MPG Enhancer
11 - all the little tweaks and adjustments outlined in the Eagle research books on mileage improvement DIY energy saving methods and devices
Like the carburetor enhancer, the hyco and the hyzor running off separate alternator to produce actual browns gas.
12 - Aerodynamic changes to car including blocking radiator, and using turbulator tape and vortex generators on various body edges
13 - Use of friction reducing lubricant additives in engine, transmission and rear end and axle bearings. With an eye toward the Diamond lube system.
14 - top cylinder oiler.
Goal is to have a large size car that gets 50 plus MPG
intake and exhaust port matching, blueprint the head to match the design spec of the ports
3 angle valve cut for the valve seat. make sure your valve seat to face witdh is the same across the whole set of heads
match valve springs
polish exhaust valves
polish exhaust ports or have them chromed
chromed exhaust manifolds
as many mechanical advantages as you can come up with to reduce friction will help. looking forward to your results.
Tom C
Sign in to reply, or ask for an account.