kywdo free energy
Started by Bodkins · · 15 posts · last reply 26 September 2009
-
#1 ·
YouTube - FREE ENERGY (with old electronic - NEW).wmv
this needs to be looked at and understood i beleive theres more here to be learnt.
I have rep. this with a single diode led white and it works.
YouTube - free energy LED
dr stifflers sec will be of great importance to helping this effect
the future will be bright! -
#2 ·
john_g sent me this link
PhET Photoelectric Effect - Light, Quantum Mechanics, Photons, Electrons -
#3 ·
Good find Bodkins on the LED post. Thanks must go to Sebosfato for the link,- he posted it on the Stan Meyer page.Bodkins wrote:
john_g sent me this link
PhET Photoelectric Effect - Light, Quantum Mechanics, Photons, Electrons -
#4 ·
-
#5 ·
This is my first post on this forum. Seems like my prediction came true again.
quantumuppercut wrote:
Well, if you have high voltage or static charge, you can make an electrostatic motor. Electromotive force is contain within the high voltage itself and constantly in oscillation. Current is always there. It is just in AC form of super high frequency that makes it useless. If you can rectify gigahertz to tetrahertz, you will have unlimited DC from any electromagnetic waves, higher than those frequency, maybe gravity wave . Current diode technology is too far behind. The magic thing about electrostatic motor is they can rectify through circulation. -
#6 ·
-
#7 ·
Finally something low enough tech, being a single component energy circuit,Bodkins wrote:
YouTube - Led giving 2.4 volt from sunlight
over two volt with one led
I think I can't screw this one up and do it wrong
As far as using LEDs goes, this guy seems to think green LEDs are better
for some reason than other colors.
"Power For Free"??? - The Whistle Post - Model Railroad Forum
Would not it be a rule that the more power hungry the LED is to light up,
the more power it would generate?
This could be neat stuff. How long will a LED last in UV light?
Will the plastic turn brittle or turn yellow?
Would a glass or ceramic diode last longer than a plastic encased LED? -
#8 ·
The sun is down right now, so I tried a 1N4007 1A 1000V Rectifier Diode up against a CFL.
The diode had wires solder to both ends so I could expose only one side of
the diode at a time to the light.
Putting the cathode end wire against the CFL read 1.5 volts.
Putting the anode end wire against the CFL read 0.45 volts.
Put some foil on the anode end with the diode in the shade and
obtained about the same reading of 1/2 a volt.
Seems the diode itself needs not be exposed to the light, just the wires.
Does this scale up?!
If I don't get distracted, remember, the sun comes out and by the
grace of my Lord, I'll try it in sunlight
Randy -
#9 ·
the diode needs to be 1n5062 white,
randy come on!!!! its PP time
LOL
-
#10 ·
also i cant charge a 2mf cap up to 2 volts from a light bulb with a magnifer on the white light led -
#11 ·
Is it a dream?
I used 4 RM2C diodes in series pulled off an old TV board,
bare wire wrapped around
the positive probe of the meter to the diodes and stuck the probe
into the middle, into the inside of a CFL. 2 volts.
Let go, do not touch the probes: 3.3 volts
To not touch the ground wire either.
Depending upon which one you touch it falsifies/effects your voltage readings.
Connect an earth ground and it jumps to 6.2 volts
Then I thought it was not good for my probe to be inside
that hot bulb, so I wrapped the bare wire around the CLF
and it started out at 6.2 and fell to 4 volts .. I don't know
Then I got to thinking .. that just isn't right. I must not
have observed it correctly. So I grab the positive probe and jammed
it inside the light bulb and let go (don't touch!)
Reading 9.9 volts.
Is this sounding crazy enough for you yet?
I ran out of same kind of diodes .. I'll look around for more.
I don't expect to get these kind of voltages from sunlight??
But but .. it would be nice......
Randy ..... hmmmm ....... -
#12 ·
I think you will get better voltage in sunlight with a magnifier. i try the transistor style cuuting the bcak off a 2n3055 but i only get .5
not try grounding yet but its a good idea!
crazy i love crazy
Im off next week will give you a call
-
#13 ·
Hey, you did understand that I get voltage without the diodeBodkins wrote:
I think you will get better voltage in sunlight with a magnifier. i try the transistor style cuuting the bcak off a 2n3055 but i only get .5
not try grounding yet but its a good idea!
crazy i love crazy
Im off next week will give you a call
being exposed to the light, only the wire connected to the diode is
exposed... Right?!
Would it not follow that surface area being exposed to the light
is a factor then, also?
I tried a piss-ant JT coil I have and i don't know what i'm doing
or the current is zip/nil. It didn't seem to do anything to the
voltage.
Yes look forward to the call.. give me a heads up so i can
schedule bed time .. i do not do a schedule and am up over
24 hours a lot. -
#14 ·
hehe i standunder that randy. we need to work out what the diode REALLY is then.
heat cold diode? light to dark?
off we go again Randy
the current is nil but serial change a cap to dump to battery.
i will order 100x1n5062
1n5062 are audio diodes i think
-
#15 ·
A thought. Does a higher voltage diode make a difference?
Does the surface area that the light falls upon make a bigger
difference than the diode itself?
The diodes you are getting are more expensive and are an avalanche diode.
Is an Avalanche or a non-Avalanche a better diode for the experiments?
The first diode I tried tried, 1N4007 1A 1000V Rectifier Diode, created
1.5 volt and is very cheap compared to the 1n5062????
Get 100 1N4007 here for $2.00 US. International Buyer pays $2.99 for shipping. Click the Buy-Now button.
I purchased 100 1N4007 for $3.75 total, my shipping was only $1.75.
I've often pondered what word to use instead of UnderStand
Remember to ask, "By who's authority?"
Sign in to reply, or ask for an account.