Bench
1,315 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
The Inductance Core (53) is composed of 'Grain Oriented' Electrical Steel laminations that step up applied voltage when magnetic field coupling crosses over from the Primary Coil-winding (26) to the S...
established VIC confidence 0.80
Total VIC 'Circuit Resistance' to D.C. current flow is expressed and determined by combining Rl (secondary pickup coil resistance), Z2 (choke-coil L1 impedance), Z3 (choke-coil L2 impedance), and Re (...
established WFC
Re, the dielectric property of water in the VIC Circuit Resistance formula, has a typical resistive value of 78.54 Ω, since rain water (85f) contains less than 20ppm of any type of contaminants due to...
established VIC
Rl, the resistive value of Secondary Pickup Coil 52 (Figure 7-8), is combined with the magnetic field strength of primary coupling field 71 in direct relationship to inductance field strength Rp, whic...
established VIC
Coil-wraps 56 and 62 (choke coils L1 and L2) are Bifilar wound together onto a single spool-bobbin, giving each choke-coil the same impedance value.
established VIC
The two VIC choke-coils L1 (coil 56) and L2 (coil 62) are wound from stainless steel (s/s) wire, each with a typical resistive value of 11.6 KΩ, determined by inductance field strength (FL1, FL2) when...
established WFC confidence 0.80
When thermal atomic agitation occurs at gas exit port (32, Figure 4-5), it spark-ignites expanding water gas-fuel (45/46/47, Figure 4-5) during the water inject cycle (70, Figure 4-5), releasing therm...
established WFC confidence 0.80
Voltage Ignition Process (90, Figure 5-5) utilizes Dynamic Voltage Potential (600, Figure 6-3) of opposite electrical stress (SS'-617-RR') to cause thermal atomic agitation (90, Figure 4-7), i.e. kine...
established WFC confidence 0.80
The Hydrogen Fracturing Process (390, Figure 3-42) is brought on and triggered once liberated and expanding water gases (100, Figure 4-8) pass beyond exit port (E9d).
established WFC
Capacitor (ER) should remain relatively small due to the dielectric value of water, in order to obtain maximum Thermal Explosive Energy-Yield (16a...16n, Figure 4-5), which subsequently establishes th...
established VIC
Inductors (L1/L2) should always have larger Reactance than Capacitor (ER, Figure 7-2) in order to maximize amp restriction, enhancing 'Voltage Deflection' (SS'-617a...617n-RR') shown in Figure 7-4.
established VIC
Plate Inductance (Lc) is the Inductance Reactance of Inductor (L1) and Inductor (L2) in series with the Resonant Capacitor (140-170 of Figure 7-6, corresponding to 690 of Figure 7-8).
established WFC
Water temperature (Rt), kept cool-to-the-touch, keeps insulation resistance (Re) constant since amp flow remains minimal.
established WFC
The dielectric property of water opposes amp leakage (Re), while another property of water takes on an 'Electrical Charge'.
established VIC
Capacitance Reactance is determined by the insulation resistance (Rs+Re) and Inductance (L1/L2) interacting together during D.C. Pulsing.
established WFC confidence 0.80
Circumference surface points (E9a - E9n) are determined from the diameter cross section (D) of the cylindrical surface using the mathematical constant (x) = 3.1416 (pi), per Figure 7-11 (720).
established WFC confidence 0.80
Surface Area (A) of the Resonant Cavity is expressed via longitudinal length (h) of the tapered resonant cavity, exit pan circumference surface point (a = E9d), and cylindrical circumference surface p...
established VIC confidence 0.80
(Eo), the Free-Space Permittivity of Water, is established by the VIC Circuit's ability to restrict amp flow; the ratio (e/Eo) is the Dielectric Constant of Water.
established WFC
Capacitance (Cp) between Electrical Voltage-Plates (E1/E2 - E9/E10) is determined by the surface area (A) of the plates, the distance (d) between plates (in inches), and the permittivity (Eo) of water...
established WFC
The dielectric property of water (78.54 ohms @ 25°C) permits storage of Electrical Charge when a potential voltage difference exists between Electrical Voltage-Plates (E1/E2 as to E9/E10).
established WFC confidence 0.80
Each resonant cavity design functions as a Voltage Wave-guide (570) with a gap-size (35) sufficient enough to allow the 'Quenching Effect' to take place, as illustrated in Figure 7-12 (730) and Figure...
established WFC
Excitor Plates (E1/E2) can be configured as: linear cylindrical resonant cavity (Tubular Cavity 730A) producing a Traveling Constant Electrical Voltage Wave; taper cylindrical resonant cavity (730B) p...
established WFC
Electrical Voltage-Plates (E1/E2), called Excitor Plates or Voltage Zones, are made of Stainless Steel T304, which does not chemically interact with liberated hydrogen, oxygen, and non-combustible gas...
established WFC
Capacitor (ER) is automatically formed when dielectric liquid water (Re) is placed between Electrical Conducting Plates (E1/E2), per Figure 1-1 (Memo WFC 420).
established VIC
The inductance formula uses N (number of turns), A (mean radius in inches), B (length of coil in inches), and C (depth of coil in inches), with L expressed in microhenries.
established VIC confidence 0.80
By optimizing distributed capacitance (Cda...Coo) and distributed inductance (Dla...Dln), the coil's Inductance Field Strength (FLa...FLn) is intensified so the coil functions as a voltage multiplier...
established VIC
Inductance (L, in microhenries) of a multi-layer coil of rectangular cross section is computed from turns (N), mean radius (A, inches), coil length (B, inches), and coil depth (C, inches). Optimizing...
established WFC confidence 0.80
Dielectric gap-spacing, denoted (Cp), is one of the parameters (along with voltage amplitude, duty cycle, gated pulse-frequency, and inductor/coil lengths) that determines the thermal explosive energy...
established VIC confidence 0.80
The text identifies a Secondary Pickup Coil (523) with a Length parameter denoted (FL3a xxx FL3n) as one of the factors influencing thermal explosive energy-yield from water.
established WFC
Thermal Explosive Energy-Yield (gtnt, 16a-16n) instantly produced from water (85) is determined by Voltage Amplitude (Vn), Duty Cycle of Pulse Train (T1-T2a...T1-T2n), Gated Pulse-Frequency of applied...