Bench
1,315 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
Amp leakage (electron coupling to water) to the water bath (68) is prevented by encapsulating the resonant cavity (57) in delrin material (72), an electrical insulator to high voltage that remains res...
established VIC
Amp restriction beyond resonant action occurs when unipolar magnetic field coupling (71) is allowed to simultaneously drop across both resonant charging chokes (56/62) during pulsing operations, since...
established VIC
Variable inductor-coil (62), similar to inductor (56) but connected to the opposite polarity voltage zone (67), further inhibits electron movement within the VIC; a movable wiper arm (73) fine-tunes t...
established VIC
Inductor (56) is composed of resistive wire to further restrict D.C. current flow beyond normal inductance reaction (Xl); pickup coil (52) is likewise made of resistive wire, contributing to total cir...
established VIC
Voltage intensity or level across the excitor array (57) can exceed 20,000 volts due to circuit (60) interaction, directly related to the variable amplitude input of the pulse train (64a-64n).
established VIC
At frequencies close to resonance, the voltage across the individual LC components (inductor 56, capacitor 57) is higher than the applied voltage (49); at exact resonant frequency the theoretical volt...
established VIC
The inductor (56) and capacitor (57) of LC circuit (180) are tuned to resonate at a given frequency; the resonant frequency (63) can be raised or lowered by changing the inductance (56) and/or capacit...
established VIC
Water becomes part of the Voltage Intensifier Circuit functioning as a resistance between electrical ground (67) and pulse-frequency positive potential (66), helping to prevent electron flow within th...
established VIC
Resonant charging choke (56) in series with the Excitor-Array (66/67) forms an inductor-capacitor circuit (180); the Excitor-Array acts as a capacitor because natural water (68) between the opposing e...
established VIC
Switching diode (55) prevents electrical shorting to the secondary coil (52) during pulse off-time by conducting only in one direction, and simultaneously acts as an electronic switch that opens the c...
established VIC
The pulsing transformer (primary coil 26 / secondary coil 52) steps up voltage amplitude during pulsing operations; primary and secondary coils have no direct electrical connection (electrically isola...
established VIC
Negative electrical ground (61) of the Voltage Intensifier Circuit (60) is electrically isolated from the primary electrical ground (48), preventing electron flow from the input circuit ground into th...
established VIC
Primary coil (26), pulsing core (53), secondary coil (52), switching diode (55), resonant charging choke (56), resonant cavity assembly (170), natural water (68), and variable resonant charging choke...
established VIC
The only electrical connection point is a voltage cross-over from the regulated power supply (150, Figure 3-6) to the battery supply (28), as illustrated in Figure 3-6.
established VIC
Although the primary coil pulse waveform (49) exactly duplicates pulse train (47), the two pulse trains are electrically isolated from each other despite the correspondence.
established VIC
The resultant pulse waveform (49a...49n) superimposed onto primary coil (26) in Figure 3-18 is an exact duplicate of the proportional pulse train (47a...47n) driving the cell driver circuit.
established VIC
The gated pulse signal (48) fed into the cell driver circuit (90) performs a switching function, turning electric ground 'off' and 'on' as applied to the opposite side (48) of primary coil (26), shown...
established
Conversely, opposite pulse shaping (narrower pulse train, wider pulse off-time) occurs when circuit (80) of Figure (3-5) is calibrated in reverse order.
established
During calibration, pulse train (44a...44n) becomes widened while pulse off-time width (43) becomes smaller, simultaneously.
established
The newly formed gated duty pulse (45) is proportional to the physical change in pulse train (44a...44n) when circuit (80) is adjusted for calibration purposes.
established
Pulse train (44a...44n) is exactly the same as pulse train (41a...41n), and its established pulse frequency (number of pulse cycles per unit time) changes uniformly when pulse generator (70) of Figure...
established
Together pulse train (44a...44n) and pulse off-time (43) form the gated pulse duty cycle (45).
established
Gated Pulse Circuit (80) of Figure (3-5) switches 'off' and 'on' sections of the incoming clock signal (42) to form gated pulse (45), which is duplicated in succession to produce gated pulse train (46...
established WFC confidence 0.80
The pulse frequency range of each clock signal (21) and (42) can be altered or changed independently of each other to obtain peak performance of the Fuel Cell System (100) of Figure (3-5).
established
Circuit (70) produces another independent and separate clock signal (41a...41n) which is electrically transmitted to and becomes the incoming clock signal (42) for the Gated Pulse Frequency Generator...
established
Increasing the number of duty pulses (39a...39n) up to a pulse frequency range of 10kHz or above forms clock signal (21) of Figure (3-5), which performs the scanning function of the Acceleration Contr...
established
Pulse on-time (37) and pulse off-time (38) are equally displaced to form duty pulse (39), which is duplicated in succession to produce pulse train (41) shown in Figure (3-16).
established
Circuit (70) of Figure (3-5) produces several clock pulses simultaneously, each with a different pulse-frequency, but all maintaining a 50% duty cycle pulse (39) configuration as shown in Figure (3-16...
established VIC confidence 0.80
In operation, Laser Accelerator Assembly (20) attenuates battery voltage potential (32a xxx 32n), which is electrically connected to the Voltage Intensifier Circuit (60).
established WFC
Gas logic circuit (310) supplies logic function to Voltage amplitude control circuit (50) to maintain proper gas pressure to gas injector (36) by electronically monitoring achieved gas pressure via pr...