min2oly
4 posts · 779 more in threads this archive does not carry · writing between Nov 2014 and Feb 2017
An identity on Energy Science Forum as it was harvested, not an account on this site. Nobody here has claimed it, and nothing connects it to a person by name.
AlvaroHN wrote:
Hi,
I got back into my little ssg motor that I posted in this thread 2~3 years ago.
At that time I had it with a bifilar coil for the motor, 1 trigger and 1 power winding. Now I made a larger coil, with 8 strands of wire, 1 trigger, 7 power.
The circuit is the same as the advanced book, but with small transistors, 2n2222. All matched up and everything.
It runs much faster!, with the old coil it ran 3000++ RPM at 12 volts. and everthing got hot, the coil and transistors.
Now with this coil I have not tryed to run it on 12v... yet.
with 5v input from a phone charger, it runs at 3600++ RPM. o.O
in the past I wondered why mine droped a lot of RPM with the gen coils in place (not connected, just drag from the iron cores). And the SSG from the advanced book didn't drop any RPM with the gen coil. Now I see that I had 1 power winding, and 6 gen coils... the SSG from the book had 7 power windings and 1 gen coil... totally different story.
I have to start new tests now, I have to get other batteries because the lifepo4 that I had at the time are not in the best shape. And I want to try with normal batts, I might get some new 6v 4ah batteries. And see what happens on 6V. It might get up to 4000 RPM.
I don't want to run it on 12V because I am afraid that those magnets escape from the rotor or something. I have to make a better frame...
I might put all 6 gen coils back in, out of phase each with independent diode charging a cap dump circuit. I also have to experiment with the AC cap that John had in the 1984 booklet in the gen coils.
here are some pics that I took just now, with 1 gen coil going to the new cap dump circuit that I made.
[ATTACH=CONFIG]5769[/ATTACH]
[ATTACH=CONFIG]5770[/ATTACH]
[ATTACH=CONFIG]5771[/ATTACH]
[ATTACH=CONFIG]5772[/ATTACH]
best
Alvaro
Try running it on your 5v and charge the 12 volts, maybe with a simple cap dump via larger transistor or just straight to the 12V...
KR - Patrick
For anyone experimenting with these lifepo4's, if you can pick them up cheap and they are well within your means, please experiment away... I picked up a couple (12V 10-14Ah $100 each) way back when they were first mentioned many many moons ago. I have not had better results with them than I have had with the FLAB's. I don't want anyone thinking this is "the answer" and spending $'s needlessly. If you are not attaining better than 1:1 with FLAB's, IMHO - these are not going to advance your research. These batteries behave VERY different than FLAB's one must re-educate and learn how they charge and discharge so as not to be fooled.
Example when fully charged, they rest about 13.25. when under C20 load they stay at 13.24 and do not drop 1/100V until the power is used. If someone has results to report that are different than my own, please do tell.
$'s are better spent on the wheel, the coils, and transistors. focus on getting a nice clean solid spike at 1:1 then add the generator/pickup coils, although, I have yet to see a demonstration from JB where he needed the pickup coils to get better than 1:1 In JB's recent DVD where he has 2 fans on the wheel and he introduces the comparator, he is getting well over 1:1 with no pickup coils using FLAB's.
Kind regards,
Patrick A.
Example when fully charged, they rest about 13.25. when under C20 load they stay at 13.24 and do not drop 1/100V until the power is used. If someone has results to report that are different than my own, please do tell.
$'s are better spent on the wheel, the coils, and transistors. focus on getting a nice clean solid spike at 1:1 then add the generator/pickup coils, although, I have yet to see a demonstration from JB where he needed the pickup coils to get better than 1:1 In JB's recent DVD where he has 2 fans on the wheel and he introduces the comparator, he is getting well over 1:1 with no pickup coils using FLAB's.
Kind regards,
Patrick A.
Aaron Murakami wrote:
The site is live -
A & P Electronic Media has now released Bedini SG - The Complete Advanced Handbook. The finale to this paradigm-shattering trilogy teaches the reader how to convert the mechanical work produced on the wheel into even more electricity, in an extremely efficient way. As a matter of fact, it is so efficient that at the recent 2014 Energy Science & Technology Conference, Peter Lindemann was able to demonstrate how to light a large bank of LEDs to a very bright level without reflecting almost any mechanical load back to the machine.
This third book also reveals many details from John Bedini's other related technologies, some of which have never been released or explained to the public before. In that sense, it also doubles as a tribute to his tireless contribution to the field of advanced energy research over the last four decades.
Learn more about this amazing trilogy at http://www.emediapress.com/go.php?offer=qiman&pid=40