Bench
424 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established WFC
Expelled non-combustible gas (D), derived from and supplied by the water bath, is captured and recycled back into the sustained hydrogen gas-flame or Fuel-Cell, causing the gas-flame temperature to be...
established WFC
The gases (B/D) that accumulate above the water bath in the Water Fuel Cell are vented for safety purposes.
established WFC
In the quiescent state, the supply of B/D gases being released from the water bath is terminated and stopped when the Fuel-Cell becomes de-energized, leaving unused water as a non-burnable liquid.
established WFC
The Water Fuel Cell produces a uniform gas-mixture (B/D, browns gas/detonation gas) regardless of the gas flow-rate of the Fuel-Cell, and only when needed.
established WFC
Natural water acts and performs as a Gas-Mixing Regulator when the Fuel-Cell is electrically energized by way of voltage stimulation, i.e. the Electrical Polarization Process.
established WFC
The Gas Retarding Process sustains and maintains an open-air flame beyond 5000 degrees F, as illustrated in Figure 2-3.
established WFC
Non-combustible gases such as Nitrogen, Argon, and other non-burnable gases derived from ambient air dissolved in natural water perform the Gas Retarding Process, which controls the hydrogen burn rate...
established WFC
The Water Fuel Cell inherently allows the Burn-Rate of Hydrogen to be changed or adjusted from 325 cm/sec to 42 cm/sec, co-equalling Natural Gas burning levels, as illustrated in Figure 2-3.
established WFC confidence 0.80
The text states that the utilization and recycling of the non-combustible gases enables the Water Fuel Cell to become a Retrofit Energy System, implying integration of the Quenching Circuit Technology...
established WFC
Electrical Repelling Forces (T-T') and (W-W') exert a 'Pushing Effect' onto already deflecting water molecules (1017/1018) since like electrical forces repel or push away from one another in a strictl...
established WFC
Alternating gated voltage pulses (B+/O-B-/O then O/B+-O/B-) cause rotational spin (1019) of water molecules for bipolar alignment, oscillating them rapidly to heat the water and also deflecting them u...
established WFC
The dielectric value of water (78.54) inhibits amp leakage into the water bath, preventing distortion of the reoccurring traveling voltage waveforms (T4Aa...T4An / T4Ba...T4Bn).
established WFC
Continued oscillation of the bipolar water molecules (1004/1006) in alternating directions produces kinetic energy (165) as the molecules collide with neighboring water molecules in the same water bat...
established WFC
Self-inductance coupling (619a...619n) automatically prevents amp influxing, restricting current flow into and away from the water bath (68) during each pulsing cycle (T4A/T4B).
established WFC
Exposing water molecule atoms to an external electrical attraction force (SS'/RR'), separately or combined with an external electrical repelling force (SS'-TT'/RR'-WW'), causes the bipolar charged wat...
established WFC
Electrical stress brought on by opposite voltage polarity in an electronic circuit is economical since the applied voltage fields propagating opposite electrical attraction forces between the bipolar...
established WFC
The greater the Electrical Stress (RU-RU' to ST-ST') applied, the greater the amount of thermal explosive energy released from the Resonant Water Gap (Cp), as shown in Figure 4-5 and Figure 10-1.
established WFC
Ever-increasing pulsating opposite electrical voltage fields with superimposed Rippling Voltage-Surfaces create a rubberbanding Pulsating Opposite Electrical Stress across the Water Gap (Cp), causing...
established WFC confidence 0.80
The Dynamic Electrical Charging Effect (612, Fig 8-1) acts as a progressive Energy Priming Stage (500, Fig 5-1) when Static State Space (790, Fig 8-3) is configured to Dynamic State Space (800, Fig 8-...
established WFC
Less water contaminants nets even higher energy-yield (gtnta through 85a-85h to gtntn), as illustrated in Water Chart (760) of Figure 7-15.
established WFC confidence 0.80
Increasing Thermal Explosive Energy-yield (gtnt) to higher energy-levels (gtnta through gtntn) beyond the applied excitation voltage (Vn) is achieved by altering Voltage Surfaces (35b/35c) relative to...
established WFC
The operational parameter is to utilize Opposite Electrical Attraction Force (SS' - RR') at high voltage intensity (Vn) to instantly release Thermal Explosive Energy (gtnt) from natural water.
established WFC
The physical force-yield (Fy) produced during gas-ignition is directly related to the liquid volume of water (85) per injection cycle and the applied Resonant Voltage Intensity (Vo-Vn), as illustrated...
established WFC confidence 0.80
During pulse on-time (T1), electron clustering occurs within the Copper Wire Zone (52), inhibiting electron flow to maintain opposite voltage potential across the Resonant Water Gap (616), which is pa...
established WFC
Re, the dielectric property of water in the VIC Circuit Resistance formula, has a typical resistive value of 78.54 Ω, since rain water (85f) contains less than 20ppm of any type of contaminants due to...
established WFC confidence 0.80
When thermal atomic agitation occurs at gas exit port (32, Figure 4-5), it spark-ignites expanding water gas-fuel (45/46/47, Figure 4-5) during the water inject cycle (70, Figure 4-5), releasing therm...
established WFC confidence 0.80
Voltage Ignition Process (90, Figure 5-5) utilizes Dynamic Voltage Potential (600, Figure 6-3) of opposite electrical stress (SS'-617-RR') to cause thermal atomic agitation (90, Figure 4-7), i.e. kine...
established WFC confidence 0.80
The Hydrogen Fracturing Process (390, Figure 3-42) is brought on and triggered once liberated and expanding water gases (100, Figure 4-8) pass beyond exit port (E9d).
established WFC
Capacitor (ER) should remain relatively small due to the dielectric value of water, in order to obtain maximum Thermal Explosive Energy-Yield (16a...16n, Figure 4-5), which subsequently establishes th...
established WFC
Water temperature (Rt), kept cool-to-the-touch, keeps insulation resistance (Re) constant since amp flow remains minimal.