Bench
451 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
The transmitted light source (3) turns on when a 5 volt electrical power source is applied to the LED (1) through dropping resistor (5) via voltage regulator (6) connected to the car electrical system...
established VIC
The linear derate of light intensity is approximately 1.25 mW per degree C above 25 degree C, measured at a spatial distance of 0.500 inches between the two infrared devices (1)(2).
established VIC
The peak wavelength transmitted from the infrared emitting diode (1) to the Optoschmitt receiver (2) is typically 935 nm, allowing the Optoschmitt clock frequency (rate of logic state change) to be 10...
established VIC
Laser Accelerator Circuit (10) uses a GaAs infrared emitting diode (1) to trigger a SDP8611 Optoschmitt light receiver (2) from quiescent state (output logic high, B+) to on-state, switching output to...
established VIC
The Voltage Intensifier Circuit (110, Figure 4-9) inhibits and prevents electron flow from entering into the gas ignition process (180), as further illustrated in Figure 4-8.
established VIC
Voltage Igniter Stage (180, Figure 4-5), together with Voltage Intensifier Circuit (110, Figure 4-9) and Extraction Circuit (10, Figure 4-10), performs several functions simultaneously to initiate and...
established VIC
A predetermined energy-flame temperature is established by adjusting fluid-medium (45/46/47) and applied voltage amplitude (V0) independently of each other to obtain the desired result.
established VIC
To lower energy-flame temperature, the amount of non-combustible gases (45a...) is increased or the fluid flow rates (45/46/47) are reduced uniformly while lowering pulse voltage amplitude (V0).
established VIC
To elevate energy-flame temperature, fluid-displacement (46/47) is increased while non-combustible gas (45) volume flow is maintained or reduced, together with an increase in applied pulse voltage amp...
established VIC
Energy-flame temperature is regulated by controlling the volume flow-rate of fluid mediums (47/45/46) in direct relationship to applied voltage intensity (33/36), per Figures 4-2 and 4-5.
established VIC
The electrical polarization and dielectric resonance also set up and trigger the Hydrogen Fracturing Process (390) of Figure 3-42 (as to Figure 3-6), controlled on demand via electrical-static spark i...
established VIC
In the Voltage Igniter Stage (180) of Figure 4-5, the water-fuel mixture is exposed to high intensity voltage fields (33/36) typically 2,000 volts or above at 10 kHz or above, of opposite electrical p...
established VIC
U.S. Patent #4,826,581, issued May 2, 1989, covers the Electrical Polarization Process.
established VIC
U.S. Patent #4,936,961, issued June 26, 1990, covers the Resonant Cavity Voltage Intensifier Circuit (VIC).
established VIC
The Voltage Intensifier Circuit brings on the 'Electrical Polarization Process' that switches off the covalent bond of the water molecule without consuming amps.
established VIC
By simply attenuating or varying voltage amplitude in direct relationship to voltage pulse-rate, Atomic Power-Yield can be determined under a controlled state.
established VIC
Absorbed Laser energy (Va, Vb, Vc) weakens the Electrical Bond between orbital electrons and the atomic nucleus; simultaneously, electrical attraction-force (qq'), stronger than normal due to lack of...
established VIC
Laser or light intensity is variable as to duty cycle on/off pulse-frequency from 1Hz to 65 Hz and above (Eq 17), where Le is light intensity in watts, T1 is current on-time, T2 is current off-time, a...
established VIC
Ohm's Law is applied for the LED circuit in a parallel array, where (It) is the forward current through the LED cluster-Array and Vcc is the applied voltage, typically 5 volts (Eq 16).
established VIC
Laser/light intensity is linear with respect to forward current through the LEDs. The specified forward current (I_led) is typically 20mA per diode, and the LED voltage drop (V_led) is typically 1.7 v...
established VIC
The absorbed Laser Energy (Electromagnetic Energy) causes many atoms to lose electrons while highly energizing the liberated combustible gas ions prior to and during thermal gas-ignition.
established VIC
Inductor (D) in relationship to inductor (C) electrically balances the opposite voltage electrical potential across voltage zones (E1) and (E2) within the Voltage Intensifier Circuit.
established VIC
The variable inductor-coil (D) has a movable wiper arm that allows fine tuning of the 'Resonant Action' during pulsing operations of the Voltage Intensifier Circuit.
established VIC
Variable inductor-coil (D), similar to inductor (C), is connected to the opposite polarity voltage zone (E2), which further inhibits electron movement or deflection within the Voltage Intensifier Circ...
established VIC
At frequency close to resonance, the voltage across individual components (inductor C, capacitor ER) is higher than the applied voltage H, and at resonant frequency the voltage VT across both inductor...
established VIC
The value of the Inductor (C), the value of the capacitor (ER), and the pulse-frequency of the applied voltage across the LC circuit together determine the impedance of the LC circuit (Eq 1, series im...
established VIC
The established resonant frequency of the LC circuit is independent of voltage amplitude, as illustrated in Figure 1-3 as to Figure 1-4.
established VIC
The resonant frequency can be raised or lowered by changing the inductance and/or capacitance values of the LC circuit.
established VIC
The Inductance (C) and Capacitance (ER) properties of the LC circuit are tuned to resonance at a certain frequency.
established VIC
The Inductor (C) becomes a Modulator Inductor, stepping up an oscillation at a given charging frequency along with the effective capacitance of a pulse-forming network to charge the voltage zones (E1/...