Bench
383 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established VIC
Secondary pickup coil (52) in Figure 3-23 is composed of individual spiral wrapped coils (505a...505n), typically .002 Ga. magnet wire, electrically connected in sequential order to form bobbin cavity...
established VIC
Primary Coil (26), typically .030 Ga. film coated magnet wire, is longitudinally wrapped in space relationship on top of and layered bidirectionally (507a...507n) across the spiral-wrap choke coils (5...
established VIC
The individual spiral-wrap coils (501a...501n) are electrically connected in sequential order to form the resistive pickup coil (503).
established VIC
The .004 Ga. (or smaller) 430F/430FR wire is axially (spiralled) bifilar wound about core bobbin (502), forming individual spiral-wrap coils (501a...501n) of equal length running from inner to outer c...
established VIC
Resonant Choke Coils (56/62) shown in Figure 3-23 (Memo WFC 422 DA) are composed of 430F or 430FR inductance stainless steel wire, film coated for high dielectric value, typically .004 gauge or smalle...
established VIC confidence 0.80
The 'Voltage Intensity of Opposite Potential' (600) generated by the VIC coil-assembly performs work to trigger the Hydrogen Fracturing Process (520), as referenced against (100) of Figure 4-8.
established VIC
The design parameters of the VIC coil-structures (580) inherently determine 'Efficiency,' defined as minimizing amp leakage, which governs how the resulting Voltage Intensity of Opposite Potential (60...
established VIC
Activation Process (590) is achieved because amp flow is restricted from entering the Voltage Triggering Process (70) by way of the voltage intensifier coil-assembly (580).
established VIC
All activation points (E9a-d) perform their functions in sequential order within an instant of time, since the applied voltage level of intensity, typically about 20,000 input volts, can be extended o...
established VIC
At activation point E9a, water flow is exposed to the voltage wave-form to begin water-to-energy conversion; at E9b voltage intensity is sufficient to perform the Electrical Polarization Process; beyo...
established VIC
The parallel sides (E9/E10) of the conical cavity function as a 'voltage wave-guide' and also act as a voltage intensifier circuit as the applied gated pulse-frequency travels the cavity length toward...
established VIC
The outer conical surface (E9) and inner conical surface (E10) form an open-air conical cavity (570) with parallel (or in other cases non-linear) voltage-surfaces spaced typically .010 gap apart, with...
established VIC
A calibrated gated unipolar pulse train (Fig 3-20) is outputted from the resonant choke (56) and electrically transmitted to the positive outer conical surface (E9), while negative voltage potential i...
established VIC
The resonant pulse-frequency is determined by the dielectric value of natural water in direct relationship to the resonant cavity's geometrical configuration; water's dielectric value is stated as 78....
established VIC
The incoming gated pulse-train (Fig 3-17) is electronically tuned to adjust pulse off-time (T2) to compensate for the rise and fall of magnetic field coupling, establishing a predetermined resonant pu...
established VIC
The voltage intensifier circuit (VIC) coil-assembly (580, Fig 6-1) is electrically interfaced with the 'Taper Resonant Cavity' (590, Fig 6-2), as schematically shown in Fig 3-22 relative to pulse core...
established VIC
The Voltage Intensifier Circuit is pulsed sensitive (49a xxx 49n) to tune into the dielectric properties of an airborne gas molecule, activating Covalent Switch-Off phenomenon (550) by restricting amp...
established VIC
The WFC Exhaust Air Reclaimer uses opposite electrical attraction force (RR'-SS') from voltage potential (Va xxx Vn) to separate the atoms of the Nitric Oxide NO molecule by overcoming the Electrovale...
established VIC
WFC Exhaust Air Reclaimer (900) of Figure (9-1) is similar in construction to Voltage Intensifier Circuit (110) of Figure (4-9), and is used to comply with the EPA Clean Air Act by eliminating Nitric...
established VIC
The repetitive polarity switching causes 'Particle Oscillation' functioning as an 'Energy Generator' through 'Physical Stress' undergoing pulsating 'Electrical Stress' whenever pulse switching cycles...
established VIC
When the (B+/B+ - B-/B- / 1030B) switch function is activated, switch terminals (T1/T2-T3/T4) are closed; switch position (T1/T4-T3/T2) reverses voltage polarity once switch function (T1/T2-T3/T4) clo...
established VIC
The circuit performs Voltage Switchover Logic Functions (B+/B+ 1030B ↔ B-/B- 1030A) of Figure 11-7 during each and every sequential voltage pulsing cycle (T4A-T4B-T4A-T4B and so on).
established VIC
Electrical Attraction Forces (S-S'/R-R') and Repelling Forces (T-T'/W-W') can be applied simultaneously or in a time sequence as the Electrical Crossover Switch Circuit (1060) reverses voltage polarit...
established VIC
The Electrical Crossover Switching Circuit (1060) singularly places either a Positive Voltage Potential (1014) across Voltage Zones E18/E14 and/or a Negative Voltage Potential across Voltage Zones E17...
established VIC
To reduce the number of VIC Circuits to a single VIC Coil Assembly (1003) while enabling a Voltage Repelling Force (W-W' and/or T-T'), the Electrical Crossover Circuit (1060) is electrically placed be...
established VIC
Varying the gated pulse-width (T4A/T4B), voltage amplitude (Vn), and Switchover pulse frequency rate (Sopr) collectively determines the rate at which water temperature rises as it travels through the...
established VIC
The electrical conductivity of T304 stainless steel together with water's dielectric property (water insulating against amp flow) sets up electrical conduction zone (587), allowing the voltage pulse w...
established VIC
The constructed tubular-array of the Differential Voltage Wave-Guide is composed of T304 stainless steel material (or equivalent), chosen for being chemically inert to the voltage deflecting process (...
established VIC
The Differential Voltage Wave-Guide (1040) is constructed with a smaller tube placed inside a much larger tube, with space between them to allow water to pass through, similar in construction to the l...
established VIC
Pairing positive zone (E13/952) with negative zone (E16/956), and (E14/953) with (E15/954), each of identical longitudinal axis length, forms the 'Differential Voltage Wave-Guide' (1040), defined by a...