Bench
424 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established WFC
The Water Fuel Cell is a patented process using a solid-state electronic control system to produce hydrogen gas on demand from water through voltage stimulation, called the Electrical Polarization Pro...
established WFC confidence 0.80
The resultant Shunting Effect allows voltage intensity across the Resonant Cavity Zone (35) to compensate for water impurity that might alter operational parameters of the Hydrogen Fracturing Process,...
established WFC
Electron restriction while varying voltage intensity is achieved by tuning the incoming pulse-train to the Dielectric Properties of Water (47), whose dielectric value of 78.54 becomes an integral part...
established WFC
Increasing the applied voltage amplitude (VL) exerts a greater magnitude of opposite Electrical-Stress (SS'-RR'/TT'-UU') across the combustible gas atoms (76, 77a-77b), ejecting a greater number of el...
established WFC
After water dissociation, the liberated gases (76, 77a-77b) undergo Energy-Priming Process (520) to attenuate electrical forces, then Electron Ejection Process (230) of Figure (29) ionizes the release...
established WFC
Once water fuel-droplets fully occupy the Resonant Cavity Zone (35) and are exposed to pulsating opposite electrical voltage fields (49/51) per voltage waveform (280) of Figure (17), the Electrical Po...
established WFC
Injected water fuel-droplets (48a-48n) surround the outer surface area of the exposed positive probe (33) while entering the Taper Resonant Cavity (180), as illustrated in Figure (3B) and Figure (14).
established WFC
The resultant water fuel-mixture (48) is pressurized up to and beyond 125 lbs of fluid-pressure by Fluid Displacement Pump (170) of Figure (13), causing water fuel-droplets (48a-48n) to form as the mi...
established WFC confidence 0.80
The distributor firing sequence is based on 25 rotor revolutions per second, which divided by 1000 gives a timing of 25ms per revolution, governing water injection timing and applied pulse-voltage tim...
established WFC
The water-fuel consumption rate of 0.47 ml/sec divided by 100 injection cycles/sec results in a 7.4 microliter water droplet per injection cycle.
established WFC confidence 0.80
50 engine revolutions/sec divided by 2 (distributor turn ratio) gives 25 rotor revolutions/sec; multiplied by 4 water-fuel injectors yields 100 injection cycles/sec.
established WFC confidence 0.80
For a 50 hp internal combustion engine with an on-road tested gasoline consumption rate of 1 ml/min, the equivalent hydrogen-fuel-of-water rate is 44.4 ml/min, converting to 0.740 ml/sec water-fuel co...
established WFC
The Water Fuel Injector Assembly can be used as a spark plug injector nozzle (130) of Figure (4-11) for both gasoline and diesel engines.
established WFC
The Water Fuel Injector Assembly can be used to produce rocket thrust, as illustrated in (160) of Figure (4-14).
established WFC
The Water Fuel Injector Assembly can be utilized in Furnace Nozzle Assembly (140) of Figure (4-12) for grain dryers or conventional heating systems.
established WFC confidence 0.80
For reciprocating engines, WFC Fuel-kits can be similar to Car design (340), while jet engines use the Water Fuel Injector kit approach instead.
established WFC
Water Fuel Injector kits (10) of Figure (4-1) can be used as a self-contained fuel-unit having no pre-pressurized vessel, converting water directly into thermal explosive energy (gtnt) on demand, as i...
established WFC
Water Fuel Injector Assembly (10) of Figure (4-1) can mechanically replace standard fuel-injector ports of existing jet engines, as shown in (150) of Figure (4-13).
established WFC
The newly established modulated Hydrogen Fuel-mixture (88 - Diesel) co-equals the spark-ignition ratio (typically .35–.39) of standard Diesel-Fuel (Fossil) under compression.
established WFC
Adjusting the burn-rate (330, Figure 3-37) of Fuel-gases (88, Figure 3-38) from 43–37 cm/s (Gasoline burning level) to 40–35 cm/s (Diesel burning level) allows the WFC Hydrogen Gas Management System t...
established WFC confidence 0.80
Resonant Action (170) not only excites the water bath but also functions and performs as a water-pump due to gas rising, enabling circulation of purified water back into the Fuel Cell.
established WFC
The Electrostatic Filter Process produces a purified water bath (156) which is recycled back into the Fuel Cell (120) of Figure 3-24, since Resonant Action (170) also functions as a water-pump (causin...
established WFC
During Resonant Action (170), liberated micro-sized contaminates (144a...144n) pass through water inlet line (145) and are deposited inside Electrostatic Filter Assembly (440), where they are exposed...
established WFC
Suspended and dissolved water contaminates (144a...144n) are typically present at 20 ppm to 40 ppm in natural water, and are uniformly released from and superimposed onto the water bath (68) during Re...
established WFC confidence 0.80
The Gas Modulator Process (320) allows hydrogen fuel cell (120) to be retrofitted to any conventional internal combustion engine (55) without engine change, simply by metering the proper amount of exh...
established WFC
The Electrical Polarization Process (160) is a physical process using opposite electrical polarity attraction force (qq') to disrupt and switch off the covalent bond between the unlike charged water m...
established WFC
Chemically inert stainless steel (T304 material) voltage zones (E1/E2) submerged in natural water (68), used with the Electrical Polarization Process (160), sustain the gas mixing ratio (88) by preven...
established WFC
Water bath (68) functions as a 'Gas Mixing Regulator' since the highest possible thermal explosive energy yield from hydrogen during normal gas ignition (98) occurs at the exact composition of water,...
established WFC
The Fuel-Gas mixture (88), formed from hydrogen (86) and oxygen (87) released from water bath (85) via the Electrical Polarization Process (160), has a hydrogen gas burn-rate of approximately 47 cm/se...
established WFC confidence 0.80
Stainless steel voltage plates (E1/E2) physically form voltage zones (66/67) regardless of the geometric shape or configuration of the resonant cavity.