Bench
1,304 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
established
Constant placement water pump (170) causes ionized ambient air gases (46), non-combustible gases (45), and water (47) to be displaced under static pressure up to and beyond 125 psi to ensure proper en...
established VIC
Exposure to the high intensity voltage fields performs the Electrical Polarization Process (160) undergoing Dielectric Resonance (240), which sets up and triggers the Hydrogen Fracturing Process (390)...
established VIC
The Water-Fuel mixture (48) enters Voltage Igniter Stage (180) and is exposed to high intensity voltage fields (33/36), typically 2,000 volts or above at 10 kHz or above, of opposite electrical polari...
established confidence 0.80
WFC Memo 424, titled 'Atomic Energy Balance of Water,' illustrates the differing electrical intensities of the charged particles composing the atom, relevant to the electrical attenuation (Aqq') proce...
established VIC
WFC memo 426, titled 'VIC Matrix Circuit,' defines the Voltage Intensifier Circuit configuration referenced for applying pulsating electrical stress to atoms as shown in Figure 5-8, item 550.
established confidence 0.80
The applied pulsating electrical stress physically 'rings' the unstable atom, attenuating the electric field strength (qq') — termed electrical attenuation Aqq' — as detailed in WFC Memo 424 'Atomic E...
established VIC
The WFC Voltage Intensifier Circuit, as defined in WFC memo 426 'VIC Matrix Circuit,' applies a high pulsating 'Electrical stress' across an unstable radioactive atom via opposite voltage potential (i...
established WFC
The Water Fuel Injector Assembly can be used as a spark plug injector nozzle (130) of Figure (4-11) for both gasoline and diesel engines.
established WFC
The Water Fuel Injector Assembly can be used to produce rocket thrust, as illustrated in (160) of Figure (4-14).
established WFC
The Water Fuel Injector Assembly can be utilized in Furnace Nozzle Assembly (140) of Figure (4-12) for grain dryers or conventional heating systems.
established WFC confidence 0.80
For reciprocating engines, WFC Fuel-kits can be similar to Car design (340), while jet engines use the Water Fuel Injector kit approach instead.
established WFC
Water Fuel Injector kits (10) of Figure (4-1) can be used as a self-contained fuel-unit having no pre-pressurized vessel, converting water directly into thermal explosive energy (gtnt) on demand, as i...
established WFC
Water Fuel Injector Assembly (10) of Figure (4-1) can mechanically replace standard fuel-injector ports of existing jet engines, as shown in (150) of Figure (4-13).
established WFC
The newly established modulated Hydrogen Fuel-mixture (88 - Diesel) co-equals the spark-ignition ratio (typically .35–.39) of standard Diesel-Fuel (Fossil) under compression.
established WFC
Adjusting the burn-rate (330, Figure 3-37) of Fuel-gases (88, Figure 3-38) from 43–37 cm/s (Gasoline burning level) to 40–35 cm/s (Diesel burning level) allows the WFC Hydrogen Gas Management System t...
established STEAM
Repetitive formation of opposite voltage pulses (166/167) at a given pulse-frequency continues to heat the water bath (68) until a desired temperature is reached.
established STEAM
The oscillating deflection of water molecules between plates E5 and E6 produces kinetic energy (165) via particle impact, which in turn heats the water bath (68).
established STEAM
By reversing to a negative voltage pulse (167), the water molecule (210) is instead deflected in the opposite direction toward voltage surface E6.
established STEAM
Once positive energized, water molecule (210) of water bath (68) is deflected toward voltage surface E5 via both opposite electrical attraction force (162) and electrical repelling force (161).
established VIC
The Voltage Intensifier Circuit (165) directly applies alternate/opposite (166/167) electrical voltage pulses, with amp restriction, in a sequential manner across voltage plates E5/E6 to activate the...
established STEAM
To ensure proper Fuel Cell operation during frigid or below-freezing conditions, the Steam Resonator assembly (450, Figure 3-46) is inserted into the Fuel Cell (120, Figure 3-24) and thermostatically...
established
Periodically back-flushing (rinsing out) the Electrostatic Filter Assembly (440) is all that is required to ensure and sustain the Electrostatic Filter Process.
established
Exposing water contaminates (144a...144n) to applied voltage fields (E1/E2) produces electrically charged contaminates (157/158) and also kills bacteria that might be present in the water bath (68).
established WFC confidence 0.80
Resonant Action (170) not only excites the water bath but also functions and performs as a water-pump due to gas rising, enabling circulation of purified water back into the Fuel Cell.
established WFC
The Electrostatic Filter Process produces a purified water bath (156) which is recycled back into the Fuel Cell (120) of Figure 3-24, since Resonant Action (170) also functions as a water-pump (causin...
established
Negative electrically charged contaminates (157a...157n) migrate to and are entrapped by positive electrical voltage post (147), while positive electrically charged contaminates (158a...158n) are attr...
established WFC
During Resonant Action (170), liberated micro-sized contaminates (144a...144n) pass through water inlet line (145) and are deposited inside Electrostatic Filter Assembly (440), where they are exposed...
established WFC
Suspended and dissolved water contaminates (144a...144n) are typically present at 20 ppm to 40 ppm in natural water, and are uniformly released from and superimposed onto the water bath (68) during Re...
established
Opposite or reverse movement of the Laser Accelerator (JJ) decreases Injectors (36) on-time which, in turn, reduces engine speed.
established
As the Laser Accelerator (JJ) advances toward 'Peak' engine performance, the Fuel-Injectors (36) open gate-time (on-time) increases proportionally.