established VIC
VIC choke coils L1 and L2 are bifilar wound on a single spool-bobbin
Coil-wraps 56 and 62 (choke coils L1 and L2) are Bifilar wound together onto a single spool-bobbin, giving each choke-coil the same impedance value.
Bench
Engineering notebook
383 published findings from the ongoing work — what has been established, calculated and observed at the bench, each traceable to the session that produced it.
-
-
established VIC
VIC choke coils L1/L2 use stainless steel wire with ~11.6 KΩ resistance
The two VIC choke-coils L1 (coil 56) and L2 (coil 62) are wound from stainless steel (s/s) wire, each with a typical resistive value of 11.6 KΩ, determined by inductance field strength (FL1, FL2) when...
-
established VIC
Inductors L1/L2 must exceed capacitor reactance to maximize voltage deflection
Inductors (L1/L2) should always have larger Reactance than Capacitor (ER, Figure 7-2) in order to maximize amp restriction, enhancing 'Voltage Deflection' (SS'-617a...617n-RR') shown in Figure 7-4.
-
established VIC
Plate Inductance is L1 and L2 in series with the Resonant Capacitor
Plate Inductance (Lc) is the Inductance Reactance of Inductor (L1) and Inductor (L2) in series with the Resonant Capacitor (140-170 of Figure 7-6, corresponding to 690 of Figure 7-8).
-
established VIC
Capacitance Reactance depends on insulation resistance and inductance during DC pulsing
Capacitance Reactance is determined by the insulation resistance (Rs+Re) and Inductance (L1/L2) interacting together during D.C. Pulsing.
-
established VIC confidence 0.80
Free-Space Permittivity of Water (Eo) is established by the VIC Circuit's ability to restrict amp flow
(Eo), the Free-Space Permittivity of Water, is established by the VIC Circuit's ability to restrict amp flow; the ratio (e/Eo) is the Dielectric Constant of Water.
-
established VIC
Inductance formula inputs are physical coil geometry variables
The inductance formula uses N (number of turns), A (mean radius in inches), B (length of coil in inches), and C (depth of coil in inches), with L expressed in microhenries.
-
established VIC confidence 0.80
VIC coil acts as voltage multiplier during switch-off
By optimizing distributed capacitance (Cda...Coo) and distributed inductance (Dla...Dln), the coil's Inductance Field Strength (FLa...FLn) is intensified so the coil functions as a voltage multiplier...
-
established VIC
Multi-layer coil inductance formula for VIC coil assembly voltage multiplication
Inductance (L, in microhenries) of a multi-layer coil of rectangular cross section is computed from turns (N), mean radius (A, inches), coil length (B, inches), and coil depth (C, inches). Optimizing...
-
established VIC confidence 0.80
Secondary Pickup Coil length is a designated parameter (FL3a-FL3n)
The text identifies a Secondary Pickup Coil (523) with a Length parameter denoted (FL3a xxx FL3n) as one of the factors influencing thermal explosive energy-yield from water.
-
established VIC
Inductor L1 and L2 are physically identical and behave identically
Inductor (L1) acts and performs in like manner to Inductor (L2) since both Inductor (L1/L2) are physically the same size and shape.
-
established VIC
Inductance Reactance determines voltage swing and establishes impedance to minimize heat loss
Inductance Reactance determines the voltage swing from the highest voltage level (Vn) to the volts switch-off point (Vff), and establishes Impedance (FL) which minimizes heat loss of electrical input...
-
established VIC
Step Charging Effect occurs when pulse off-time is less than on-time
Inductance Reactance effectuates the 'Step Charging Effect' (680, per Figure 7-7) when the Pulse off-time (T2) is less than the Pulse on-time (T1).
-
established VIC
Inductance Reactance doubles input frequency at 50% duty cycle
Inductance Reactance doubles the input frequency (64a * 64b) when a 50% Duty Cycle Pulse (T1 = T2) is inputted, while also increasing applied voltage amplitude (Vo-Vn).
-
established VIC
Stored energy is controlled by input voltage amplitude and gated pulse frequency
Inductance Reactance directly determines Stored Energy (Wa), which is controlled by the input Voltage Potential as attenuated or varied via Voltage Amplitude (Vo, Va, Vb-Vf, Vg-Vn, per Figure 7-13) an...
-
established VIC
Stored energy formula for inductance
Stored energy (Wa) in Joules (Watt-seconds) is a function of Inductance (L) in Henries and current (I) in amperes, per the stated energy relationship for Inductance Reactance.
-
established VIC
Lengthening L1/L2 inductors raises voltage potential across Resonant Capacitor (ER)
Lengthening the Inductor (L1/L2) lengths applies an even higher Voltage Potential (66/67) across the Resonant Capacitor (140-170, labeled ER), because Inductance Reactance stores energy.
-
established VIC
Voltage Inducement Process occurs without amp influx between positive and negative voltage potentials across Resonant Cavities
The electromagnetic coupling fields encourage the Voltage Inducement Process across the VIC Impedance Network Circuit without amp 'influxing' (i.e., inhibiting amp flow) between the Positive Voltage P...
-
established VIC
430F/430FR stainless steel wire is electromagnetically inductive without becoming permanently magnetized
The Electron Inhibiting Effect combined with the Voltage Enhancement Effect is achieved because stainless steel 430F/FR wire-material is electromagnetically inductive to incoming flux lines without th...
-
established VIC
Higher amplitude pulses drive coupling field through both inductors, increasing opposite-polarity voltage across the Resonant Cavity
At elevated voltage amplitudes, the primary electromagnetic coupling field (Rp), transmitted via the Inductance Pulsing-Core through the VIC Coil Assembly, passes through both Inductors L1 and L2 simu...
-
established VIC
Electron Inhibiting Effect prevents electron flow/arc-over across the water capacitor gap
The blocking action of L2's field prevents and inhibits electron flow from passing through or arcing over the capacitor water-gap (Cp); this is termed the 'Electron Inhibiting Effect' (631).
-
established VIC
L1's field performs Capacitance Charging Effect while L2's field restricts electron flow
Inductance Field L1-FL1 performs the 'Capacitance Charging Effect' (628), while at the same time Inductor Field L2-FL2 restricts electron movement through the VIC Impedance Network Circuit by locking...
-
established VIC
Pulse frequency is tuned to water's dielectric property to minimize current while maximizing voltage
Adjusting the programmable pulse-waveform input signal frequency 'tunes-in' to the dielectric property (Re) of water, reducing amp flow to a minimum while allowing voltage potential to rise toward inf...
-
established VIC
L1 and L2 are bifilar wound in equal length for matched electromagnetic field strength
Both Inductors L1 and L2 are bifilar wound in equal length so their electromagnetic field intensities are equal (FL1 = FL2), promoting the 'Electron Bounce' phenomenon.
-
established VIC
Inductors L1-L2 act as Resonant Charging Chokes forming the Resonant Voltage Effect Circuit
Inductors L1-L2 (Figure 7-6), placed on opposite sides of the water-capacitor ER, act as Resonant Charging Chokes (614/615) and together form the Resonant Voltage Effect Circuit (670).
-
established VIC
Inductance Reactance increases voltage across water-capacitor beyond applied voltage potential
Inductance Reactance occurs when resistance (Rs), capacitance (Cd), and Inductance (FL) interact during D.C. Pulsing, increasing voltage across the water-capacitor (ER) beyond the applied Voltage Pote...
-
established VIC
VIC dielectric coatings rated 3KV/mil across -40C to 155C automotive range
All dielectric coatings on the VIC wire have an effective 3KV per mil dielectric value and are formulated to endure the automotive temperature range from -40°C to 155°C.
-
established VIC
VIC magnet wires use solderable Nysol polyurethane nylon jacket insulation
Both magnet wire sizes (622/623), the Primary and Secondary Pickup Coils, use solderable Nysol (Polyurethane Nylon Jacket) insulation enamel coating as an electrical shield-material.
-
established VIC
VIC choke wire uses Pyre-ML/Himol polymer coating for thermal/mechanical resistance
The stainless steel resonant charging choke wire (614/615) is coated with the 'Pyre-ML' trade name 'Himol' polymer coating-material to impart thermal and mechanical resistance.
-
established VIC
VIC Secondary Pickup Coil uses 35 AWG copper wire at 13K ohms/lb
The Secondary Pickup Coil (623) of the VIC uses 35 AWG (.007 in) copper wire equal to 13K ohms per pound weight.